Aerial friction rigging devices: what TCI and the makers describe
Tree Care Industry magazine describes friction taken up into the tree, and a TCI-reported field test found that fixed anchors cut stem strain by about one-third. The load in the rope on the falling piece stayed the same.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The named training bodies and researchers are described here as published. It is not training and does not teach the work. The sources are two articles from TCI Magazine, the publication of the Tree Care Industry Association, and a 2009 paper in Arboriculture and Urban Forestry. No maker's description of an overhead friction device was opened for this page, so devices appear by type, not by brand.
Friction taken up into the tree
Lawrence Schultz's July 2023 TCI article on taking friction up into the tree traces aerial friction back to the trunk wrap. Before blocks, pulleys and lowering devices, ground crews walked coils of three-strand rope around the trunk to control a rigged piece. Schultz lists the shortcomings of that method. Adding and removing wraps was slow, the amount of friction was hard to modulate, the rope could mark up the trunk, and the wrap tied up a ground person completely.
Taking the wraps up into the tree changed four things, as Schultz describes them. The shorter end of rope was easier to wrap. A small-diameter limb gave slightly more control of the friction than a trunk. The trunk of a tree being kept was left unmarked. After the load was arrested, the ground person could pass the lowering duty to a nearby climber and free a set of hands for processing.
Schultz is an ISA Certified Arborist and contract climber in the San Francisco Bay area. The article is based on his TCI EXPO 2022 presentation on tight-quarters rigging and aerial friction. Where it gives an opinion, it is his: the value of an aerial friction device depends on the type of work and the size of the crew, and any new tool has a learning curve.
Forces at the rigging point
Schultz's diagram shows a frictionless overhead rigging point, which can see double the weight of a load at a static standstill. The input force that holds the load must be at least equal to the load. Friction at the point helps hold the load against gravity, so the input force does less work. In theory, he writes, adding friction reduces the force on one leg of the rope and so at the rigging point. He calls aerial friction useful in general and more so on a compromised tree or wherever forces are to be kept to a minimum.
Rope construction and hardware
Schultz cites a sketch from a TCIA rigging manual for arboriculture. Three-strand, 12-strand and 16-strand ropes suit natural-crotch rigging because they have no core, or a core that does not bear load. Double-braid and kernmantle ropes share the load between cover and core. If friction damages the cover, the core does a disproportionate share of the work. Double-braid rope is best suited to smooth-surfaced hardware.
Devices that create aerial friction work by bending, wrapping or pressing the rope, and most are made of aluminum, which dissipates friction heat. Schultz names consistency as one of the main benefits over raw bark: the number of wraps needed on a large limb differs from a small one, while the device gives the same ride every time. Many devices have adjustments or settings for the amount of friction.
The TCI-reported field test
Matt Follett and four co-authors summarised two studies in TCI Magazine in July 2022. The first compared fixed anchors with a rotating block under a running rope. The subject was an 18-inch (45 cm) DBH green ash, with the rigged notch 24 feet 7 inches (7.5 m) above ground and a piece of 425 pounds (93 kg). A ramp-and-cart rig stood in for a ground person letting the rope run. Four anchors were tested, one rotating block and three stationary devices, three drops each. Strain gauges, a load cell and an accelerometer measured the results.
| Measure | Fixed anchors against the rotating block |
|---|---|
| Load at the lowering device on the ground | Routinely about half |
| Peak stem strain | About one-third lower |
| Estimated load at the upper anchor | Lower, by a similar amount to the stem strain |
| Load in the lead rope on the falling piece | Not reduced; no significant difference for one of the anchors against the block |
The authors explain that the potential energy to dissipate is the same, so only a longer time to slow the piece lowers the peak load in the lead rope. They add that the reduction is for a running-rope, best case scenario. They also write that climbers feel the lower load on the stem and anchor, and may be inclined to take a larger piece than the lead rope and its attachment can bear.
Earlier measurements
The TCI authors cite Kane (2019) in Urban Forestry and Urban Greening. In a negative-rigging test, a load dropped into the system from above and stopped abruptly, rigging rings and a block gave little difference in peak loads.
Kane, Brena and Autio, Arboriculture and Urban Forestry, March 2009, measured 13 red pines rigged with a block and a friction wrap device. Force at the block was slightly more than double the tension in the rope, and mass of the piece was the best predictor of both. The paper reports Donzelli (1999) finding that friction in the block cut rope tension between the block and the friction device by 4 percent to 30 percent for a 227 kg mass, depending on the block. The authors write that advances in rigging gear and techniques may give climbers more confidence to take bigger pieces, and that few studies had measured the breaking strength of large shade trees.
Sources
- Tree Care Industry Magazine (TCIA), Lawrence Schultz, article on taking friction up into the tree, July 1, 2023, read October 19, 2026
- Tree Care Industry Magazine (TCIA), Matt Follett and others, Testing Equipment and Techniques to Reduce Loads on the Stem, July 1, 2022, read October 19, 2026
- Arboriculture and Urban Forestry, Kane, Brena and Autio, Forces and Stresses Generated During Rigging Operations, 35(2), March 2009, read October 19, 2026