Aerial lift operator training: what OSHA 1910.67 and OSHA's own guidance say
OSHA's aerial lift rule, 29 CFR 1910.67, has one training sentence: only trained persons shall operate an aerial lift. OSHA's 1975 letter and its fact sheet fill in what that training covers.
Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The sources are the text of 29 CFR 1910.67 on vehicle-mounted work platforms, an OSHA letter of interpretation dated July 17, 1975, and OSHA's Aerial Lifts fact sheet (DSG 4/2011).
At a glance
| Item | What the sources record |
|---|---|
| Rule | 1910.67(c)(2)(ii): only trained persons shall operate an aerial lift |
| Covers | Extensible and articulating boom platforms under paragraph (c)(2) |
| Who sets the training | The employer (1975 letter) |
| Outside certification | Not required by the wording of 1910.67 (1975 letter) |
| Retraining | After an accident, a newly found hazard or a different type of lift (fact sheet) |
Aerial lifts in the rule
An aerial device is any vehicle-mounted device, telescoping or articulating or both, used to position personnel. Section 1910.67 names the types: extensible boom platforms, aerial ladders, articulating boom platforms and vertical towers, or a mix of them. It treats them as aerial lifts whether or not they rotate about a vertical axis, and whether the equipment is metal, wood or fibreglass reinforced plastic. A mobile unit is the aerial device together with its vehicle and related equipment.
Paragraph (c)(2), on extensible and articulating boom platforms, holds the training sentence in item (ii). The section gives no course length, curriculum, test or card for it. Design and construction follow the 1969 American National Standard for vehicle mounted work platforms, ANSI A92.2, for lifts acquired on or after July 1, 1975.
Operator rules in the same paragraph
Paragraph (c)(2) sits alongside other rules that bear on the operator's work:
- Lift controls are tested each day before use.
- Employees stand firmly on the basket floor, and sitting or climbing on the basket edge, or using planks or ladders as a work position, is not allowed.
- Belting off to an adjacent pole, structure or equipment is not permitted.
- A personal fall arrest or travel restraint system that meets subpart I is worn and attached to the boom or basket.
- Boom and basket load limits set by the manufacturer are not exceeded.
- Brakes are set, outriggers sit on pads or a solid surface, and wheel chocks go on before use on an incline.
- Lower controls are not operated without permission from the employee in the lift, except in an emergency.
- Climbers are not worn while working from an aerial lift.
- Before travel, the boom is inspected to see it is cradled and outriggers are stowed.
For operations near overhead electric lines, paragraph (b)(4) sends the reader to section 1910.333(c)(3).
OSHA's 1975 letter
A July 17, 1975 letter from OSHA's Division of Occupational Safety Programming answered a letter from the general manager of an insurance company about aerial ladders and booms. OSHA wrote that nothing in the wording of 1910.67 requires an employer to certify and designate an operator to another party. The employer is responsible for devising methods to train operators in the safe operation of aerial lifts, and only competent and careful operators should be assigned the work. The operator is to be trained in safe operations and made familiar with the manufacturer's manual, especially the parts on operation, maintenance and safety of aerial devices. OSHA's interpretation notice adds that letters explain requirements and cannot create additional employer obligations.
OSHA's fact sheet on training
OSHA's Aerial Lifts fact sheet says only trained and authorized persons are allowed to operate an aerial lift. It lists what training should include:
- explanations of electrical, fall and falling-object hazards;
- procedures for dealing with those hazards;
- recognizing and avoiding unsafe conditions in the work setting;
- instruction in correct operation of the lift, including maximum intended load and load capacity;
- demonstrations of the skills and knowledge needed to operate a lift before operating it on the job;
- when and how to perform inspections; and
- the manufacturer's requirements.
The fact sheet lists three triggers for retraining: an accident during aerial lift use, discovery of workplace hazards involving an aerial lift, and use of a different type of aerial lift. Employers are also required to retrain workers they see operating a lift improperly. The standards that apply are 29 CFR 1910.67, 1910.269(p), 1926.21, 1926.453 and 1926.502, plus ANSI/SIA A92.2-1969, A92.3, A92.5 and A92.6. The fact sheet carries a notice that it imposes no new compliance requirements.
Where the sources stop
None of the three documents defines "trained" by hours or by a named course. The regulation uses one word and the fact sheet uses a topic list. For bucket trucks and platforms in tree work by country, see bucket trucks and EWPs.
Sources
- U.S. Department of Labor, OSHA, 29 CFR 1910.67 aerial lifts rule, read October 15, 2026
- Cornell Law School Legal Information Institute, 29 CFR 1910.67, eCFR text, read October 15, 2026
- U.S. Department of Labor, OSHA, Training and competency of aerial lift operators, letter of interpretation, July 17, 1975, read October 15, 2026
- U.S. Department of Labor, OSHA, Aerial Lifts fact sheet, DSG 4/2011, read October 15, 2026