ArbNation Join free

ANSI Z60.1 and Canadian nursery stock standards: caliper, tree types and root-ball sizes

ANSI Z60.1 sets how nursery trees are measured and described: caliper at 6 or 12 inches, four tree types, container classes and root-ball diameters. Canada has its own Canadian Nursery Stock Standard, first issued in 1967.

Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The American text below is ANSI Z60.1-2004, approved May 12, 2004, as published by the American Nursery and Landscape Association. The figures are those of the 2004 edition.

Measuring caliper and height

Section 1.1.1.2 of the 2004 edition sets the method. Caliper is taken 6 inches above the ground for trunks up to and including 4 inches. If the caliper at 6 inches is over 4 inches, it is taken at 12 inches. A diameter tape gives the most accurate reading because trunks are seldom round. Readings from a slot or pincer caliper are the average of the smallest and largest measurements.

Height is measured from ground level for field-grown stock and from the soil line for container-grown stock, which should sit at or near the top of the root flare. A size designation names only the minimum of its interval. A specification for 2.5 in. caliper therefore refers to the 2.5 to 3 inch interval.

Tree types and what a specification must state

Z60.1 splits trees into four types. The height-to-caliper table below covers Type 1 shade trees. Type 2 shade trees grow more slowly, and their height should not be less than two-thirds of the Type 1 figure. The last two types are small upright trees (Type 3) and small spreading trees (Type 4).

Type 1 shade trees: caliper and height (Table 1)
CaliperAverage height rangeTypical maximum height
1 in.8 to 10 ft.11 ft.
2 in.12 to 14 ft.16 ft.
3 in.14 to 16 ft.18 ft.
4 in.16 to 18 ft.22 ft.
5 in.18 ft. and up26 ft.

Required specifications depend on how the tree was grown. Bare root and field-grown stock state size by height or caliper. Container and box stock add a container class or box size. Fabric bag stock states caliper and a minimum bag size.

For Type 1 and Type 2 field-grown shade trees, size is caliper, and caliper takes precedence over height if both are given. Type 3 and Type 4 trees are sized by height through the 5 to 6 foot interval and by caliper after that.

Section 1.1.2.3 says that when "specimen" or "quality grade" trees are called for, the specification must state the characteristics wanted, such as symmetry, crown width, fullness of branching or a single dominant leader. Street tree bids must state the height to which the trunk is free of branching.

Container classes

A container-grown specification must give both a plant size and a container class marked with the "#" symbol. Each class spans a band of volumes. Class #1, for example, runs from 152 to 251 cubic inches. A specification that names only gallons or quarts is not in accordance with the standard. The standard applies to trade transactions, not retail consumer sales.

Root-ball sizes

Table 6 gives recommended minimum root-ball diameters for field-grown trees. They assume stock grown in the ground without containers or fabric bags and dug with the ball intact. Minimum ball size is not a required specification. The standard's stated aim is a ball that holds enough fibrous and feeding root system for the plant to recover fully.

Minimum root-ball diameter for Type 1 and Type 2 shade trees (Table 6)
CaliperMinimum root-ball diameter
1 in.16 in.
1 1/2 in.20 in.
2 in.24 in.
3 in.32 in.
4 in.42 in.
6 in.60 in.
8 in.80 in.

Ball depth is measured from the root flare, and soil above the flare is not counted. The trunk should sit in the centre of the ball, with a tolerance of 10 percent of the ball diameter. Burlap or other material around the ball must be biodegradable and must completely cover it. Ball-supporting devices such as wire baskets, if used, must hold the ball firm and rigid.

The Canadian Nursery Stock Standard

Landscape Ontario reported in June 2017 that the ninth edition of the Canadian Nursery Stock Standard had been released. The standard was first published in 1967 as a guide to minimum production standards for nursery stock. A committee of growers from all regions of Canada produced the ninth edition over two years, after consulting landscape architects and municipalities. It is a downloadable PDF from the Canadian Nursery Landscape Association.

The Canadian Society of Landscape Architects and the Canadian Nursery Landscape Association placed the standard inside the Canadian Landscape Standard, where it replaces Section 12, Container Grown Plants.

Sources