Back-leaners and heavy lean: what the codes and IFSG 302 publish on pulling and wedging
WorkSafe New Zealand calls felling against the lean back-pulling and sets rules for the rope, the machine and the signals. SafeWork NSW, WorkSafeBC, HSE and the Irish guide each treat lean and pulling aids in their own terms.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
The named codes and training bodies are described here as published. It is not training and does not teach the work.
WorkSafe New Zealand: back-pulling
Section 3.4.5 of the arboriculture code is titled felling against the lean of the tree (back-pulling). Everyone carrying out a back-pull is competent or training under adequate supervision. The machinery is adequate for every part of the operation and used for its intended purpose and as the maker instructs. The faller and the machine or equipment operator have an effective means of communication, which may need an intermediary. The rope should be secured as high on the tree as practicable, given tree size, lean and height and the pulling capacity of the machine. If two tree lengths of clearance are possible, the tree may be pulled towards the machine or the equipment anchor.
The planning list in section 3.4.1 names the lean of the tree, and decayed or weak spots including in the hinge area. The same section says a pulling line should be attached to all trees and stems being felled where assisted directional felling is required. Where a tree is large enough to cause harm, wedges, block and tackle, rope, wire cable or other devices are used. Section 3.4.6 adds that no one stays in the bight of a working rope, that line pull stays within the safe working load, and that the feller tells winch and machine operators beforehand the line tension and speeds needed.
SafeWork NSW: natural lean and controlled directional felling
The Tree works code of practice, commenced on 27 March 2026, treats clear felling and controlled directional felling together in section 9.1. For clear felling, with at least two tree lengths of open space on every side, the specific controls are to use the tree's natural lean and hinge placement to control the fall, with wedges as needed.
Controlled directional felling is for limited space, under two tree lengths, or where the natural fall direction would create hazards. It controls the fall with ropes, cables or mobile plant. For ropes and cables the code lists these points.
- Anchor points capable of holding the total load, away from the drop zone if vehicles or plant are the anchors.
- Ropes, cables and winches rated for the expected loads.
- A number of ropes that matches the arc of the drop zone, for example at least two for arcs of 180 to 90 degrees.
- Ropes set high in the tree to control fall direction, with tree defects or multiple trunks considered when choosing anchors.
Pushing uses suitable mobile plant only. When plant assists, the code has it positioned ideally in line with the intended fall and applying only enough pressure to prevent the tree sitting back while cuts are made. The operator stays in the cab until the tree is committed to fall, and ground workers stay outside the drop zone once cutting begins.
WorkSafeBC: direction of lean
Section 26.24(5)(e) of the British Columbia regulation has wedging tools immediately available and, unless the tree has a pronounced favourable lean, wedges set. For dangerous trees, section 26.26 says to fell in the direction of lean whenever possible, with an undercut as deep as needed to minimise wedge use and the vibration it causes. Pushing with a green tree is only to overcome a falling difficulty. Wedging over is used only when no alternative exists, after a careful assessment of whether the dangerous tree can take wedging.
HSE and the Irish guide
HSE names three pulling practices to avoid: free hand pulling on a non-anchored line, over-tensioned lines that can sever the hinge early or split the tree, and making the back cut while a workmate applies tension. On signals it has the chainsaw operator in control and any unclear signal read as stop.
IFSG 302, a leaflet modified for Irish use by kind permission of the Forest Industry Safety Accord, covers basic felling where no pulling aids are needed. It lists aid tools that may be needed as a breaking bar or felling lever, a sledgehammer, wedges, a hydraulic toe jack and a hand winch with handle, cable, pulleys and strops. Where the tree may move and trap the saw, appropriate aid tools or techniques are used.
Sources
- WorkSafe New Zealand, approved code of practice for safety and health in arboriculture, sections 3.4.1, 3.4.5 and 3.4.6, read October 16, 2026
- SafeWork NSW, Tree works code of practice, March 2026, section 9, read October 16, 2026
- WorkSafeBC, Occupational Health and Safety Regulation, Part 26 Forestry Operations, sections 26.24 and 26.26, read October 16, 2026
- Health and Safety Executive, Working with chainsaws, read October 16, 2026
- Health and Safety Executive, Winches in directional felling, read October 16, 2026
- Health and Safety Authority and Teagasc, IFSG 302 Basic Chainsaw Felling and Manual Takedown, October 2018, read October 16, 2026