Bar and chain oil, and guide bar wear: what makers and regulators say
Chain oil and guide bar condition, from the safety bodies of the United Kingdom, Canada and Western Australia. Two makers' own figures on their chain oils and on the point where a guide bar is worn.
Checked against the sources at the bottom of this page on October 9, 2026. Rules, fees and pay change: the source has the last word.
Safety bodies and makers print the statements below about saw chain oil and the guide bar. Nothing here says how to oil, fit or retire a bar. Chain pitch, gauge and file sizes are covered in the guide to chain pitch, gauge and file size by maker, and the regulators' pre-use lists in the guide to chainsaw pre-use checks.
What the safety bodies print
- HSE, Great Britain. The leaflet AFAG308 on top-handled chainsaws (revision 2, April 2013) has a checklist to run before work and periodically through the day that includes the question whether the chain oiling system is working. For the moment before a saw is passed up to the climber it asks whether oil delivery to the chain is okay. Its maintenance checklist includes a check of the guide bar rails for cracks and distortion.
- WorkSafe Western Australia. Its chainsaws page, updated April 1, 2025, lists among the general precautions a check that bar oil is flowing and the chain brake is working. It also says to top up with bar oil each time the operator stops to refill with fuel. Its field maintenance list names bar oil among the items kept nearby during extensive cutting.
- CCOHS, Canada. The maintenance and service fact sheet, last revised April 24, 2024, has a heading on chain lubrication. It says to follow the maker's instructions, check that the chain is receiving oil, and use the correct grade and type of chain saw oil. The oil level is checked when refilling, because many saws need oil at the same time as fuel. Under the chain and guide bar heading, the bar is replaced if nicked or distorted. The bar and chain are replaced if the bar is damaged, and a worn or damaged drive sprocket is replaced before it damages the chain. Sawdust can block the chain-oil portal.
None of the three pages names a brand or a grade of oil. WorkSafe WA and CCOHS refer the reader to the maker's manual.
Makers' declared figures for chain oil
These are the makers' own claims, not test results. The first two rows carry the date codes shown on the maker's page. The third page carries no date.
| Maker and product as named | Base and lowest temperature the maker states | Other statements on the page |
|---|---|---|
| Husqvarna, X-Guard Bar and Chain Oil, All Season (date code 2024-08) | Virgin base stock oils; 15°F / -9°C | Reduced sling formulation with a tackifier additive; anti-wear additives |
| Husqvarna, X-Guard Biodegradable Bar and Chain Oil (date code 2022-12) | Vegetable based; 0°F / -17°C | Biodegrades within 28 days |
| STIHL, BioPlus chain oil (Australian page) | Vegetable based; flowable to -20°C | Shelf life 4 years; KWF test mark and EU Ecolabel; tested to OECD 301 B; canister 25% recycled material |
The first two pages describe the tackifier as the additive that keeps the lubrication on the cutting equipment and makes longer lasting strings of oil. The storage page of the third maker, published July 13, 2023, mentions a second oil of that maker, a semi-synthetic one. The pages listed here state no base, temperature or shelf life for that oil, so it has no row.
Oil in storage on the STIHL UK page
STIHL's UK page on chainsaw storage, published July 13, 2023, says that with a biodegradable chain oil the chain lubricant tank is filled to the top before storage to prevent the oil from gumming. Semi-synthetic oils do not gum and can stay in the tank without topping up. The maker also lists draining the fuel tank, running the saw at idle until it stops, removing the chain and guide bar, cleaning them and spraying them with protective oil. Those lines are the maker's, written for its own saws and oils.
Guide bar wear points on the STIHL UK page
STIHL's UK page on when to replace a chain, sprocket or guide bar describes rail wear this way. Over time the rails of the guide bar wear and the groove depth shrinks, which is the room left for the drive links. If the groove is too shallow, the tips of the drive links scrape along the bottom. Turning the guide bar over can wear both sides evenly. A minimum groove depth is given for each chain pitch, measured with the tip of the depth gauge tool in its filing kits. Below the minimum, the bar is due for replacement. A chain run without bar oil, or tensioned too tightly over long periods, wears the underside wear marker of the tooth early.
| Chain pitch | Minimum groove depth STIHL UK lists |
|---|---|
| 1/4" P | 4 mm |
| 1/4" | 4 mm |
| 3/8" P | 5 mm |
| .325" | 6 mm |
| 3/8" | 6 mm |
| .404" | 7 mm |
On the STIHL UK page, the sprocket is replaced when the depth of the wear marks reaches about 0.5 mm, and a control gauge can be used on rim and spur sprockets. The CCOHS and HSE pages above give no groove depth figure.
Gaps in the sources
None of the pages listed here says anything about substitute oils, used oil, or which of the oils above suits which saw. None ranks oils.
Guide bar wear in maker manuals
Sources
- HSE, leaflet AFAG308 Top-handled chainsaws, revision 2, April 2013, read October 9, 2026
- WorkSafe Western Australia, chainsaws, updated April 1, 2025, read October 9, 2026
- CCOHS, chainsaws maintenance and service fact sheet, revised April 24, 2024, read October 9, 2026
- Husqvarna, X-Guard bar and chain oil product page, date code 2024-08, read October 9, 2026
- Husqvarna, X-Guard biodegradable bar and chain oil product page, date code 2022-12, read October 9, 2026
- STIHL Australia, BioPlus chain oil product page, read October 9, 2026
- STIHL UK, when to replace your chainsaw chain, sprocket or guide bar, read October 9, 2026
- STIHL UK, chainsaw storage and care tips, published July 13, 2023, read October 9, 2026