Buying a used saw: the safety devices that regulators and makers list
The Irish HSA and three saw makers each name the safety devices a petrol saw carries and the checks on them. OSHA and Washington set an age line for chain brakes: saws placed in service after an effective date need one.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The named regulators and makers are described here as published. It is not training and does not teach the work.
The Irish HSA list
The Health and Safety Authority's leaflet IFSG 301, Using Petrol-Driven Chainsaws, opens its equipment section with the words "Only use a chainsaw if". The conditions that follow name the devices.
- The stop switch works and is plainly marked.
- The front hand guard or chain brake, the chain catcher and the anti-vibration mounts are undamaged and functional.
- The throttle opens only when the throttle lock is depressed.
- The chain is a type the maker recommends, and it is a reduced-kickback type.
- The exhaust system and silencer are in good order.
- A mandatory hearing protection symbol is on the saw.
The leaflet adds checks through the working day: the on and off switch, the chain brake, the chain standing still at idle and the chain oiling system.
What three makers print
| Maker | Devices and conditions in the manual |
|---|---|
| Maker A | The before-starting list covers the operation of the chain brake and front hand guard, a correctly mounted guide bar and a correctly tensioned chain. It also names a trigger and trigger lockout that move freely and spring back to idle, and a master control lever that moves easily to stop. The manual bars modifying the controls or safety devices in any way. It says not to use the machine with a damaged or missing muffler. The chain catcher is inspected and replaced if damaged |
| Maker B | The pre-use list covers the chain brake, the rear right hand guard, the throttle trigger lockout, the stop switch, handles free from oil, the anti-vibration system, the muffler and tight fastenings. The safety equipment chapter adds a brake band at least 0.024 inch (0.6 mm) thick at its thinnest point. It also names a front hand guard without cracks and fixed to the clutch cover, and an undamaged chain catcher. A machine with a faulty muffler is never used |
| Maker C | The standard features list names a front hand guard, a rear hand guard, an anti-vibration device, a spiked bumper, a throttle control lockout, a chain catcher and a spark arrestor muffler. For the operator's own safety the manual says not to remove the chain brake system. It warns that improper replacement parts or removed safety devices may cause serious or fatal injury. It also says not to run a saw that is damaged, improperly adjusted or not completely and securely assembled |
Maker A's manual notes that the chain brake works only if the hand guard has not been modified in any way. Maker B's manual says all servicing and repair of the machine's safety equipment needs special training, and that the maker recommends its servicing dealer when a check fails.
Age lines in the rules
OSHA's logging standard, 29 CFR 1910.266(e), sets a date split. Each chain saw placed into initial service after the effective date of the section must have a chain brake and must otherwise meet ANSI B175.1-1991. Each saw placed into service before that date must have a protective device that minimizes kickback, and no kickback device may be removed or disabled. A gasoline-powered saw must also have a continuous pressure throttle control that stops the chain when the throttle is released.
Washington's chapter 296-54 WAC repeats the split in section 296-54-537 and prints the date, February 9, 1995. Before that date a saw needs a device such as a reduced kickback bar or chain, a bar tip guard or a chain brake. The chapter also prohibits a saw with a faulty clutch and requires a positive means of stopping the engine.
The guide on vintage saws and safety standards follows how the standards changed over the years. The guide on chainsaw safety features covers the features the standards name.
Sources
- Health and Safety Authority (Ireland), Irish Forestry Safety Guide IFSG 301 Using Petrol-Driven Chainsaws, October 2018, read October 19, 2026
- Chainsaw maker A, instruction manual, document 0458-153-8321-C (English), read October 19, 2026
- Chainsaw maker B, operator's manual (English), read October 19, 2026
- Chainsaw maker C, operator's manual, January 2024 edition, read October 19, 2026
- US OSHA, 29 CFR 1910.266 logging operations (eCFR), read October 19, 2026
- Washington State Legislature, chapter 296-54 WAC safety standards for logging operations, read October 19, 2026