ArbNation Join free

Carburettor H, L and T screws: what makers print and what EPA rules say about adjusting

One maker's manual fits limiters to the H and L needles, another removed the needles and the T-screw, and a third calibrates by electronics. EPA's rule for handheld engines covers any adjustment within the practically adjustable range.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

The named regulators and makers are described here as published. It is not training and does not teach the work.

What the letters stand for

Maker C's manual labels the carburettor adjustments with the symbols H, L and T. H is the high speed mixture, L is the low speed mixture and T is the idle speed. The manual says each unit is run at the factory with the carburettor set in compliance with emission regulations. It adds that the carburettor carries needle adjustment limiters on H and L that prevent settings outside acceptable limits.

Three makers, three approaches

MakerWhat the manual says about adjusting
Maker AAn electronic system adjusts the saw to optimum power during operation. A separate calibration routine exists, and the version of the system is shown on the approval label. The maintenance chart lists the carburettor with the line "check idle adjustment", and the saw chain must not rotate. If the chain keeps moving at idle, the manual has the dealer check and repair the saw
Maker BThe engine has an automatic system, so manual adjustment of the carburettor's H and L needles and the T-screw "no longer applies". Both needles and the T-screw have been removed. The system sets the high speed part during loaded running and the idle part when the saw has idled for some time. If the chain rotates at idle, the manual says to contact the servicing dealer and not to use the saw until it is adjusted or repaired
Maker CThe manual prints an adjustment routine, with limiters on H and L and a break-in of at least two tanks of fuel before any carburettor adjustment. Idle speed can be adjusted during break-in. When adjustment is finished the chain should not move at idle. For carburettor trouble the manual says to contact the dealer

Maker A's manual adds a fuel point. Gasoline with more than 10 % alcohol can impair performance in engines with manually adjustable carburettors, while engines with the electronic system deliver full power on gasoline with up to 27 % alcohol.

All three manuals say the chain must not move at idle. Maker B's troubleshooting table also sends an engine that will not idle properly to the servicing dealer.

Altitude

Maker C's manual says the engine is factory-adjusted for starting and durability up to 335 m (1,100 ft) above sea level, which it gives as 96.0 kPa. Above that height the carburettor might need adjusting by an authorized service dealer. An engine adjusted for altitude must be readjusted when it works below 335 m, or severe engine damage can result.

The federal rule has a matching line. Section 1054.115(c) requires engines to meet the standards at all specified atmospheric pressures, except that below 94.0 kPa an altitude kit may be relied on for testing. A maker that relies on an altitude kit must give the altitude range in the owner's manual. It must also state that running the engine in the wrong configuration at a given altitude may increase emissions and reduce fuel efficiency and performance.

The federal rule

EPA's Phase 2 rule for new nonroad spark-ignition handheld engines at or below 19 kilowatts covers engines used mainly in trimmers, leaf blowers and chainsaws. It was published April 25, 2000, with standards phased in from the 2002 model year. The page cites 40 CFR parts 90 and 91. Part 1054 of the same title, covering new small nonroad spark-ignition engines and equipment, also reaches handheld engines.

Section 1054.115(b) of part 1054 covers adjustable parameters. An engine with adjustable parameters must meet every requirement of the part for any adjustment in the practically adjustable range. EPA may require a maker to set the parameters to any specification within that range during testing, including certification, production-line and in-use testing. A maker may ask EPA to limit idle-speed or carburettor adjustments to a smaller range by showing the engine will not be adjusted outside it in use without a major loss of performance. The general provisions on adjustable parameters are in 40 CFR 1068.50.

Section 1054.115(e) bars a defeat device, meaning an auxiliary emission control device that reduces the effectiveness of emission controls under conditions the engine may reasonably meet in normal operation. The guide on saw modifications and emissions tampering rules covers the tampering side. The guide on chainsaw emissions rules by jurisdiction covers the other regulators.

Sources