ArbNation Join free

Chain brake test and inspection: the checks regulators and makers print

Ireland's HSA and HSE list a chain brake check among the tests of a running petrol saw. Four makers print their own test, and the speed and method differ from manual to manual.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

The named regulators and makers are described here as published. It is not training and does not teach the work.

The regulators

The Irish Health and Safety Authority's leaflet IFSG 301 puts the chain brake in two places. Its starting section lists a check that the brake works correctly. Its maintenance section lists periodic checks through the day: the on and off switch, the chain brake, a chain that stands still at idle without the brake applied, and the chain oiling system.

HSE's leaflet INDG317, Chainsaws at work, lists checks to make once a cold saw has started and the throttle has been revved to warm it up. One of them is that the chain brake is effective when applied at maximum revs or according to the maker's specification. The same leaflet names the chain brake among the parts to report when daily checks show damage or excessive wear.

Neither leaflet describes the test movements. Both send the reader to the maker's handbook for the saw.

The test as each maker prints it

MakerTest in the manual
Maker ABefore starting work, with the engine at idle speed, the brake is engaged by pushing the hand guard toward the bar nose. The throttle is then opened wide for no more than 3 seconds, and the chain must not rotate. The hand guard must be free of dirt and easily moveable
Maker BTwo checks. For the inertia release, the saw is held over a stump with the engine off, the front handle is let go and the bar drops toward the stump, and the brake should activate when the bar hits it. For the manual trigger, the saw runs on firm ground at full throttle and the brake is activated by tilting the left wrist forward onto the front hand guard. The chain should stop immediately
Maker CTwo checks. For the manual brake, the engine runs at fast idle until warm, and the brake lever is operated slowly while the saw is held firmly on the ground. When the lever trips, the chain should stop. For the automatic brake, the engine is off, the guide bar is held about 35 cm (14 in.) above a wooden surface and the bar tip is dropped onto it. The impact should lock the brake
Maker DWith the engine at moderate speed, the hand guard is pressed with the back of the hand until the brake engages. The chain should stop immediately. The throttle and then the brake are released at once

The engine speeds differ. HSE names maximum revs or the maker's specification. Maker A uses idle, with the throttle opened wide for up to 3 seconds. Maker C uses fast idle, and Maker D uses moderate speed.

Frequency, wear and a failed check

Maker A's manual puts the function test before starting work. Testing before each work session is what Maker B recommends, noting that dirt and wear can impair the brake. In Maker C's manual the brake is confirmed before each use and kept clean, because wood chips in the brake can make it work less well. Maker D's manual advises against working with the saw without first checking the chain brake.

The makers also set a wear check. A minimum brake band thickness of 0.024 inch (0.6 mm) at the thinnest point appears in Maker B's manual. Maker A describes the brake as subject to normal wear and sets dealer maintenance intervals: quarterly for full-time use, every six months for part-time use and annually for occasional use. Maker D calls the brake a very important safety device that wears like any other component, with inspection by its service centre.

When the chain does not stop, all four manuals send the saw to a dealer or service centre. Maker A adds that the engine is switched off at once on a malfunction. Maker D advises against using the saw, and Maker C returns it to the authorized dealer.

Standards the makers cite

Maker C's manual names ANSI B175.1 for the United States and CSA Z62.1 and Z62.3 for Canada. ANSI B175.1 and CSA Z62.1.3 require the brake to stop the chain in 0.12 seconds at an engine speed of 13,500 RPM. The manual also puts servicing, adjusting and testing of the brake on the owner or operator. The guide on kickback and chain brakes covers the standards in detail.

Sources