Saw chain cutter types and sequences: how the makers describe them
Saw chain is sold by cutter shape and by how the cutters are spaced along the loop. One maker lists five cutter types and three sequences, two more label their chains in their own wording, and the Canadian safety centre covers kickback-reducing chain.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The wording below comes from the makers named and from the Canadian Centre for Occupational Health and Safety (CCOHS). None of this covers filing, fitting or use, and nothing is ranked. The guide to chain pitch, gauge and file size by maker has the pitch, gauge and drive link counts. Kickback and chain brakes get their own guide, chain brakes and kickback.
Cutter types as one maker lists them
The saw chain terminology page of one chain maker lists five cutter types: chipper, semi-chisel, chamfer-chisel, micro-chisel and chisel. The parts of a cutter are top plate, cutting corner, slide plate, gullet, depth gauge, heel, rivet hole and toe. The gullet is the recessed area between cutting teeth that helps chip removal, and the depth gauge is the part that controls how much material is removed on each pass.
That page answers why a chisel chain cuts faster. A rounded cutter goes over the same end grain several times before the kerf reaches its full width, while a square chisel cutter makes the full-width kerf on every pass. The kerf is the width of material removed by the cutting.
Sequences
The maker also names three sequences: standard, semi-skip and skip. The standard sequence is ideal for general-purpose cutting. The semi-skip and skip sequences are the ones for work where clearing chips matters, for example in larger diameter wood. No other detail is given on the three.
How the makers label their chains
| Maker and chain | Cutter wording | Other wording |
|---|---|---|
| Husqvarna, X-CUT C83, 3/8 inch pitch, .050 inch gauge | Full chisel cutter, profile listed as chisel; "square corner cutters (C)" | Described as a full chisel, high-performance chain for full-time professional forestry saws. Square corner cutters are recommended for professional chainsaw users in clean conditions |
| Husqvarna, X-CUT S35G, .325 inch pitch, .058 inch gauge | Semi-chisel cutter; "round corner cutters (S)" | Guarded drive link (G) listed as the added feature and described as less prone to kickback. The specification table lists the kickback reduction as a bumper drive link |
| STIHL, Picco Super 3 Pro, for 3/8 inch P (1.1 mm) | Low profile full chisel tooth saw chain | Listed on the maker's UK range page |
| Oregon, chain letter M and chain letter R in the maintenance manual's letter identification list | M: round-ground chisel cutters with bumper drive links. R: ripping chain with Micro Chisel cutters and standard sequence | M is described as specially built for effective cutting in extremely dirty or abrasive conditions |
The first two chain pages in the table carry the model letters as part of the name: C for square corner, S for round corner and G for a guarded drive link. Both pages say the chain is sold sharpened and pre-stretched, and both list a golden-colored tie strap. The UK range page in the third row lists chains in every performance class and describes virtually all of its chains as comfort chains, marked with the letter C engraved on the tooth. Engraved markings on the teeth also indicate wear. The UK range page also describes three guide bar types, Rollomatic E, Rollomatic ES and Duromatic, and the Duromatic type has carbide plating on the bar nose. That is a feature of the bar and not a carbide cutter.
Low kickback and reduced kickback chain
The CCOHS fact sheet on chainsaw kickback, last revised August 22, 2023, quotes the CSA Z62.3-11 (R2021) definition of kickback. It is the rapid upward motion of the guide bar when the chain near the nose contacts an object, or the backward motion when wood closes in and pinches the chain. The fact sheet lists "low kickback saw chain" and "reduced kickback saw chain" next to the chain brake as kickback-reducing devices. Such devices should be designed for the saw they are used on and meet standards such as CSA Z62.3-11 (R2021) or ANSI B175.1-2021. They reduce kickback but do not prevent it.
The makers' wording differs from the CCOHS terms. The S35G page in the table says "low kickback" under its feature list for the guarded drive link and "reduced kickback" in its short description, while its specification table says "Kickback reduction: bumper drive link".
Gaps in the sources
None of the pages gives an edge-holding comparison between cutter types, a filing method for each type, or a statement about which cutter suits which saw size. The maker that lists the sequences prints no spacing figures for them.
Sources
- Oregon Products, Saw Chain Anatomy and Terminology, read October 9, 2026
- Husqvarna US, X-CUT S35G chain, .325 pitch, .058 gauge, read October 9, 2026
- Husqvarna US, X-CUT C83 chain, 3/8 pitch, .050 gauge, read October 9, 2026
- STIHL UK, saw chains and guide bars, read October 9, 2026
- Canadian Centre for Occupational Health and Safety, Chainsaws: Kickback, revised August 22, 2023, read October 9, 2026
- Oregon Products, saw chain maintenance manual, chain letter identification, read October 19, 2026