Chain tension: what makers' manuals and HSE publish about checks and new chain
HSE and Ireland's HSA list chain tension among the checks on a petrol saw. Three saw makers and a chain maker print their own descriptions, and three of the four address a new chain.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
The named regulators and makers are described here as published. It is not training and does not teach the work.
The regulators
HSE's leaflet INDG317, Chainsaws at work, lists, among the checks when preparing to use a chainsaw, that the saw chain is correctly tensioned. The Irish Health and Safety Authority's leaflet IFSG 301 puts a tension check among its maintenance steps, and it names a method: pulling the chain fully round the guide bar in the running direction, with gloves or a cloth. Neither leaflet gives a gap, a force or a turn count. Both send the reader to the maker's handbook.
Published descriptions of correct tension
| Maker | Published description |
|---|---|
| Maker A | Snug against the underside of the bar, yet still moved along the bar by hand when the chain is cold. At operating temperature the chain stretches and begins to sag, and the drive links must not come out of the bar groove |
| Maker B | Not sagging from the underside of the bar, yet still turned easily by hand. As tight as possible, but not so tight that it cannot be pulled round freely by hand. A slack chain may jump off the bar |
| Maker C | As tight as possible, but so it can still be pulled easily along the bar by hand. A loose chain is not to be operated |
| Chain maker E | The lowest tie straps and cutters come up and just touch the bottom of the bar rail on a solid-nose bar. A sprocket-nose bar needs more: solid contact, then an additional quarter turn of the adjusting screw |
The word "snug" or "tight" appears, but every saw maker ties it to a hand test. None prints a measured gap in millimetres or inches.
How often
Every refuel is the interval in Maker B's manual. Maker C's asks for frequent checks during work, with correction as necessary, and Maker A's asks for frequent checks too. The chain maker lists tensioning before each use and often, or at each refuelling. It also advises against tensioning right after cutting, because a chain tightened while hot can cool and shrink, leaving the tension too tight.
The reason given is stretch. Maker B notes that the more a chain is used, the longer it becomes. The chain maker calls incorrect tension the cause of more chain and bar problems than any other single factor. Maker B's newer manual adds that incorrect tension increases wear on the guide bar, the chain and the drive sprocket.
New chain
Three of the four sources address a new chain. Maker A's manual states that a new chain must be retensioned more often than one that has been in use for some time. Maker B describes a running-in period during which tension is checked more frequently. The chain maker lists a break-in routine: run the new chain at half throttle for several minutes, stop, let it cool, then check and adjust tension often, especially during the first half hour of use.
Where the sources differ
The cold and hot readings do not match. Maker A reads a cold chain as snug and a chain at operating temperature as sagging. The chain maker reads a chain tensioned hot as likely to end up too tight once it cools. Both agree that temperature changes the reading. The nose type matters to the chain maker alone: its sprocket-nose bars take more tension than its solid-nose bars, and the saw manuals above do not split the description by bar type.
For the other parts of the routine, see the guides on pre-use checks by regulator and on bar and chain oil and bar wear.
Sources
- HSE, Chainsaws at work INDG317 (rev2, January 2013), read October 19, 2026
- Health and Safety Authority (Ireland), Irish Forestry Safety Guide IFSG 301 Using Petrol-Driven Chainsaws, October 2018, read October 19, 2026
- Chainsaw maker A, instruction manual, document 0458-153-8321-C (English), read October 19, 2026
- Chainsaw maker B, operator's manual (English), read October 19, 2026
- Chainsaw maker B, operator's manual dated November 19, 2024, read October 19, 2026
- Chainsaw maker C, operator's manual for a petrol saw, document X7503255505, 2024 edition, read October 19, 2026
- Chainsaw maker C, operator's manual for a second petrol saw (2015), read October 19, 2026
- Chain maker E, saw chain, guide bar and sprocket maintenance manual, read October 19, 2026