ArbNation Join free

Chainsaw kickback: how CCOHS, the HSA, OSHA and the IEC standard define it

CCOHS quotes CSA Z62.3 for two kinds of kickback, rotational and pinch. The Irish HSA places the kickback zone at the top tip of the bar, and OSHA requires a chain brake on saws placed in service after its logging rule took effect.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The named regulators and standards are described below as published. It is not training and does not teach the work.

The definitions

The Canadian Centre for Occupational Health and Safety (CCOHS) calls kickback the unexpected upward motion of the guide bar. It occurs when the end portion of the bar nose, the kickback zone, strikes an object and the chain momentarily snags or is pinched. The same fact sheet quotes the CSA Z62.3-11 (R2021) definition, which has two forms. Rotational kickback is the rapid upward motion of the bar when the chain near the nose, on the top of the bar, contacts an object such as a log or branch. Pinch kickback is the backward motion when wood closes in and pinches the chain in the cut.

The Irish Health and Safety Authority (HSA) leaflet IFSG 301 defines it as the uncontrolled upward and/or backward motion of the guide bar. It happens when the nose of the bar contacts an object such as a log or branch, or when the wood pinches the chain in the cut. A figure in the leaflet labels the kickback zone. A second HSA leaflet, Guidance on Safe Use of Chainsaws, calls kickback one of the more common causes of serious chainsaw injury and puts the kickback zone at the top tip of the chainsaw bar.

The two zone descriptions differ in wording. CCOHS gives the end portion of the nose, and the HSA gives the top tip of the bar. Both sources say contact in that area can throw the bar toward the operator, with a risk of very serious or fatal injury.

Standards and regulations that name kickback

Where kickback appears in standards and rules
DocumentWhat it says
CSA Z62.3-11 (R2021) and ANSI B175.1-2021, as cited by CCOHSKickback-reducing devices include a chain brake, low kickback chain and reduced kickback chain. CCOHS says these devices reduce but do not prevent kickback
OSHA, 29 CFR 1910.266(e)(2)(i)A saw placed in initial service after the rule's effective date has a chain brake and meets ANSI B175.1-1991. Earlier saws have a protective device that minimizes kickback, and no kickback device is removed or disabled
OSHA, 1910.266(h)(2)(vii)The backcut is above the horizontal facecut to give an adequate platform to prevent kickback, with an exception for tree pulling
BS EN ISO 11681-1:2011, published January 31, 2012, withdrawn June 21, 2022Covers hand-held combustion-engine saws for forest work by one operator. Kickback and balance are outside it for engines over 80 cm3
IEC 62841-4-1:2017+AMD1:2024 (edition 1.1)Electric chain saws for cutting wood, for one person. Chain brake means stopping the chain manually or non-manually when kickback occurs

The kickback test and brake performance standards

The IEC standard for electric chain saws lists its normative references. Two of them are ISO 9518:2018, Forestry machinery, Portable chain-saws, Kickback test, and ISO 13772:2009, Portable chain saws, Non-manually actuated chain brake performance. It defines a non-manually activated chain brake as one triggered by kickback motion independent of operator activation, and a manually activated brake as one triggered by the operator's hand.

The IEC scope does not extend to chain saws for tree service as defined in ISO 11681-2 or to pole-mounted pruners. A note in the standard says pole-mounted pruners will be covered by a future part of IEC 62841.

HSA: chain type and brake

Leaflet IFSG 301 says a chainsaw is used only if its front hand guard and chain brake, chain catcher and anti-vibration mounts are undamaged and functional. It adds that the saw is fitted with a chain the manufacturer recommends and that reduces kickback. The companion HSA guidance lists the chain brake among the safety features to be in working order, and tells operators not to cut with the top tip of the bar.

Chain brakes have their own page, kickback and chain brakes. Standards by country are in chain saw standards by country.

Sources