ArbNation Join free

Chainsaw milling: what regulators print about ripping logs with a chainsaw

No regulator page written for chainsaw mills turned up. California's section 6282 has two lines on ripping logs, section 6283 covers portable chain saws, and HSE's leaflet INDG317 covers hand-held petrol saws.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

Everything below is what the named codes and training bodies publish about ripping logs with a chainsaw. It is not training and does not teach the work. The sources are two sections of the California Code of Regulations, Title 8, and two HSE publications. Neither source covers Alaskan mills, chainsaw mills or milling attachments.

No page on chainsaw mills

The HSE page on Chainsaws at work opens with a short description. The leaflet gives guidance on portable, hand-held, petrol-engine chainsaws at work. It is aimed at employers, the self-employed and those who control work equipment. Its topic list runs from fitness to operate a chainsaw and young workers through to tree felling and working off the ground. Milling is not on the list. HSE's sawmilling guidance, HSG172, treats the hand-held chainsaw as a tool for trimming individual logs in a mill, not as the mill.

California's Logging and Sawmill Safety Orders, Subchapter 13 of Title 8, are the one place a rule on ripping a log with a saw was found. They sit in Article 5, Falling and Bucking.

California, section 6282: Ripping Logs

Section 6282 has two subsections, in full.

  • Subsection (a): logs shall be securely chocked or strapped before they are ripped.
  • Subsection (b): if workers walk the log to rip it, sufficient holding wood shall be left, or other positive means used, to prevent splitting before they dismount to complete the cut.

The department's history note lists an amendment of subsection (a) operative November 23, 2001. The section does not name a chainsaw or a mill. It says nothing about guide bar length, rail systems or a mill frame.

California, section 6283: Portable Chain Saw Operations

Section 6283 applies to employees such as fallers, buckers, limbers, choppers and landing chasers who operate chain saws. The Department of Industrial Relations posts it for convenience and makes no warranty that it is current. The main provisions:

SubsectionWhat the section requires
(a)Leg protection labeled as meeting ASTM F 1897-98. Exceptions: high climbers, and employees who use a saw incidental to their tasks with the employer's concurrence
(b)A chain brake and a label stating the saw meets ANSI B175.1-1991 on each saw placed in service on or after May 5, 1995. Older saws carry a device that minimizes kickback, and no kickback device is removed or disabled
(d), (g), (i)A control that returns the saw to idling speed when released; a clutch that will not engage the chain at idle; a positive off-and-on switch
(e)Motors stopped when the saw is carried farther than tree to tree, not more than 100 feet, or in hazardous conditions; idle speed for short carries
(f)Exhaust manifolds built and maintained so fumes are directed away from the operator

Subsection (m) puts the duty on the employer to instruct and enforce a safe practice procedure that includes these rules:

  • inspect the saw daily for handles, guards, controls and muffler;
  • instruct operators on safe operation and adjustment;
  • keep a firm grip, and start the saw only when firmly supported and at least 10 feet from the fueling area;
  • fuel only in conditions not conducive to fire hazards, and never use saw fuel to start fires or as a cleaning solvent;
  • use proper methods to avoid kickbacks.

The section does not carve out a case for a saw clamped in a mill. Whether a milling rig counts as a portable chain saw operation is not answered on the page.

HSE: Chainsaws at work, INDG317

The leaflet, series code INDG317 (rev2), listed as published in 2012 and updated August 7, 2025 on the HSE page, says anyone who uses a chainsaw at work must receive adequate training and be competent for that type of work. For tree work it quotes the Approved Code of Practice to the Provision and Use of Work Equipment Regulations 1998. A worker should have appropriate training and a relevant certificate of competence or national competence award before using a chainsaw on or in a tree. The exception is a worker undergoing such training under adequate supervision. A narrow agricultural exception follows.

The leaflet suggests refresher training every two to three years for occasional users and every five years for full-time users. It sets out risk assessment as a legal duty and asks employers to think about new and young workers, lone workers and people with particular requirements.

HSG172, the HSE guide to sawmilling, covers the hand-held saw in a mill. Most mills keep one to trim individual logs before processing, and the operator needs training for the jobs they will do. Nobody should help the operator by holding the timber being sawn, because of the risk from the chainsaw. Its risk assessment list names fitness, young people, health risks, training, selecting and maintaining the saw, protective equipment, lone working, first aid and work off the ground. Static cross-cut chainsaws can carry a guide bar of 2 m or more. Where the cross-cut is triggered automatically by the timber or controlled remotely, HSG172 says guards should prevent access to the cutting area to the safety distances in BS EN ISO 13857:2008.

Related pages

Sawmill hazards and noise figures are in sawmilling and chainsaw milling. Leg protection labels are in chainsaw protection, and the kind of mill machine in sawmill types.

Sources