Chipper deaths: OSHA's 39 deaths of 1996 to 2005 and what NIOSH and state reports add
OSHA counted 39 chipper deaths from 1996 to 2005, and 78 percent were workers caught in the machine. A New York review of 113 deaths from 1982 to 2016 found struck-by deaths outnumbered caught-in deaths.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
The named codes and training bodies are described here as published. It is not training and does not teach the work. No victim is named, and the cases below come from the agencies' own write-ups.
OSHA's count, 1996 to 2005
OSHA's Safety and Health Information Bulletin 04-16-2008, Hazards of Wood Chippers, uses its Integrated Management Information System. It records 39 employees killed in chipper accidents from 1996 to 2005. The vast majority, 78 percent, were caught in the chipper. Most of the rest were struck by something.
The bulletin is advisory. It says it is not a standard or regulation and creates no new legal obligations. A chipper has a powered feed mechanism, knives on a rotating disc or drum, and an engine. The knives turn at about 1,000 to 2,000 revolutions per minute.
It reports two OSHA investigations.
- Caught-in, Denver area office. An operator was pulled into a chipper while feeding branches. He usually stood to the side of the feed table to reach the feed control bar, but this time he stood directly in front of the infeed chute. His leather gloves had cuffs. OSHA says a branch may have snagged a cuff and pulled him in. The chipper met the ANSI requirement for quick-stop and reverse feed devices.
- Struck-by, Boise area office. A chipper had a winch line assembly. A slack section of the line tangled in a limb being fed in and was pulled into the cutter drum. The line and choker snapped back and fatally struck the operator in the head, though he wore ANSI-approved head protection.
NIOSH Hazard ID 8
NIOSH published Hazard ID 8 in August 1999 as publication 99-145. It cites the Bureau of Labor Statistics Census of Fatal Occupational Injuries: 11 workers died from 1992 through 1997 while working near mobile wood chippers. In seven cases the victim was caught by the feed mechanism and pulled through the knives. In four the victim was struck by a hood that came off after being opened or closed while the knives still turned.
NIOSH also received two reports of deaths in 1998 through its FACE program. Its two case studies show the pattern. A groundsman was pulled into a chipper in a townhouse yard, and investigators concluded he fell or reached into the hopper. A municipal waste facility laborer was killed by a flying hood after he opened it before the disc stopped. The hood hinges were damaged.
NIOSH's prevention list for caught-in deaths includes tested emergency shut-off devices and training based on the maker's recommendations. It also lists at least two workers in close contact, no cuffs on gloves or trousers, and hands and feet kept outside the hopper. For hood strikes it lists a daily inspection of latches, pins and hinges and a closed and latched hood before starting. It adds a low-speed listening check and a full stop of internal parts before the hood opens.
The 2004 and 2018 reviews
The CDC's Morbidity and Mortality Weekly Report of December 10, 2004 carried a note by Timothy Struttmann on fatal and nonfatal injuries involving wood chippers in the United States from 1992 to 2002. Its abstract says operators can be pulled into the feed mechanism or struck by the hood opened or closed while knives still turn, and that training, maintenance and protective equipment can prevent such injuries.
Zhu and Gelberg, of the New York State Department of Health, reviewed four online databases for the American Journal of Industrial Medicine in December 2018. They found 113 chipper-related worker deaths from 1982 to 2016.
| Type of event | Deaths |
|---|---|
| Struck-by | 57 |
| Caught-in | 41 |
| Motor vehicle | 7 |
| Electrical | 4 |
| Fall | 2 |
| Heat stroke | 2 |
The authors conclude that the deaths are preventable and that young and inexperienced workers may be at higher risk of caught-in deaths. They also conclude that current feed wheel control devices are not effective for self-rescue, and that fully automatic feed wheel stop devices are needed.
The two counts differ in method and years. OSHA's 39 deaths come from its Integrated Management Information System for 1996 to 2005. The New York count is a 35-year review of four databases, and its largest group is struck-by.
OSHA's publication list
OSHA's chipper page lists two items: the Chipper Machine Safety QuickCard (OSHA 3279, 2005) and the 2008 bulletin. Quick-stop and reverse devices are covered under chipper infeed controls. A New York chipper death has its own FACE report page.
To correct or remove an entry, write to the address at the foot of this page.
Sources
- US Department of Labor, OSHA, Hazards of Wood Chippers, Safety and Health Information Bulletin SHIB 04-16-2008, read October 16, 2026
- NIOSH, Hazard ID 8: Injury Associated with Working Near or Operating Wood Chippers, publication 99-145, August 1999, read October 16, 2026
- CDC, MMWR vol. 53 no. 48, Fatal and Nonfatal Occupational Injuries Involving Wood Chippers, United States, 1992 to 2002, December 10, 2004 (CDC Stacks record), read October 16, 2026
- Zhu and Gelberg, Occupational fatal injuries associated with mobile hand-fed wood chippers, American Journal of Industrial Medicine 61(12), December 2018 (CDC Stacks record, abstract checked against PubMed), read October 16, 2026
- US Department of Labor, OSHA, Chipper Machine publications list, read October 16, 2026