Chipper emergency stops and feed controls: OSHA, HSE, SafeWork NSW and California
OSHA, HSE, SafeWork NSW and California each word the chipper stop device differently. Only SafeWork NSW prints a two-operator rule, for chippers with no in-feed stop control or a chute tray under 600 mm.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
The named codes and training bodies are described here as published. It is not training and does not teach the work. Binding rules and advisory guidance are labelled as such, because the documents differ in force.
Side by side
| Regulator and document | Stop device and feed controls | Second person |
|---|---|---|
| OSHA, bulletin SHIB 04-16-2008 (advisory) | The bulletin says ANSI Z133.1-2006 requires chippers with a mechanical feed control bar to have quick-stop and reverse feed devices. Centre is neutral and stops the rollers. Toward the discharge spout reverses them. It also lists maker devices: a bottom feed stop bar triggered by 34 pounds of force, pull ropes, a panic bar and a rubber curtain. | Recommends designating one or more employees as a safety watch near the emergency shut-off devices while others feed. |
| HSE, information sheet AIS38 revision 1, December 2013 (guidance) | A protection device on the sides and the top or bottom edge of the infeed chute, which stops the rollers when pushed in the feeding direction. On chutes under 600 mm it stops or reverses them when pulled against the feeding direction. The design must let the operator work it with body parts other than the hands. | No second-person wording in the sheet. |
| SafeWork NSW, woodchipper guide, operator control devices (guidance) | An emergency stop or shut-off that immediately stops the in-feed rollers and cuts power to the cutting disc or drum. It is tested in each pre-start check. The control bar shows reverse, neutral/stop, feed and reverse. | Two operators for chippers with no in-feed stop control or a tray under 600 mm high. |
| California Title 8, section 3424(c)(6) (binding) | Disk-type chippers with a mechanical infeed must have a quick stop and reversing device. The lever runs across the top and along each side of the hopper, as close to the feed end as practicable and within easy reach. | No second-person wording in the quoted text. |
| WorkSafeBC | Regulation wording not confirmed. A 2005 incident report summary records a driven-feed mobile chipper without a panic bar to act as an emergency stop. | Not confirmed. |
OSHA
The bulletin is not a standard or regulation, and it creates no new legal obligations. Its enforceable references are the machine guarding rules, 29 CFR 1910.212(a)(1) and (a)(3), and the logging standard, 29 CFR 1910.266(h)(4), which requires infeed and outfeed chutes to be guarded against contact with the disc, knives or blades where it applies.
OSHA lists the devices without ranking them. The bottom feed stop bar cuts all power. The maker says it cannot be retrofitted to older models. The pull ropes reverse the rollers, may be hard to find if tangled in branches, and can be retrofitted. The panic bar stops the hydraulic system driving the rollers and is not attached to the feed control bar.
HSE
AIS38 describes operator protection at the infeed chutes of power-fed mobile chippers. New machines supplied on or after 27 June 2005 must comply with BS EN 13525:2005+A2:2009. The sheet's own dimensions are for older machines, set by the height of the chute's lower edge: under 600 mm, 600 mm and above, and machines supplied before 31 October 2000.
For a lower edge under 600 mm, the distance from any chute edge to the rollers is at least 1200 mm, and the floor slopes downward from the rollers. HSE sets the protection device to cover at least 75 percent of each vertical side projection and 100 percent of the horizontal projection. It must not need more than 150 N on the horizontal part, or 200 N elsewhere on the 75 percent projection.
After the device stops the rollers, they restart only through a secondary control. HSE names a latch, a detent needing force in more than one direction, or a control system that holds the stop until a separate reset. HSE says following its guidance is not compulsory, but doing so will normally be enough to comply with the law.
SafeWork NSW
The guide adds that the device should be immediately accessible to the operators. It suggests side in-feed stop control bars where the tray is under 600 mm. It also mentions bump bars, last chance stops that need a free hand, and presence-sensing safeguards. The full wording is in chipper infeed controls.
California
The California Occupational Safety and Health Standards Board decided Petition File No. 549 on January 21, 2016. The petition asked for a passive presence-sensing stop device on tree and brush chippers. The Board's decision describes the existing rule: sections 3424 and 4299 require the quick stop and reversing device only on rotating disk chippers with a mechanical infeed. They do not require it on rotary drum chippers with a mechanical infeed.
The Board staff review dated December 21, 2015 quotes section 3424(c)(6) and notes that stop bars along the base of the hopper are another method makers use. Section 3424 covers tree work, and section 4299 has almost identical wording for other industries.
Sources
- US Department of Labor, OSHA, Hazards of Wood Chippers, Safety and Health Information Bulletin SHIB 04-16-2008, read October 16, 2026
- Health and Safety Executive, Power-fed mobile wood chippers: Operator protection at infeed chutes, Agriculture Information Sheet AIS38 (rev 1), 12/13, read October 16, 2026
- SafeWork NSW, Woodchipper guide, Operator control devices, read October 16, 2026
- California Occupational Safety and Health Standards Board, Petition File No. 549 decision, January 21, 2016, read October 16, 2026
- California Occupational Safety and Health Standards Board, Board staff's review of Petition File No. 549, December 21, 2015, read October 16, 2026
- WorkSafeBC, incident investigation report summary: Ground worker pulled into mobile wood chipper, July 2005, read October 16, 2026