ArbNation Join free

Chipper infeed controls: quick-stop, reverse and feed-bar wording in OSHA SHIB 2008, SafeWork NSW and EN 13525

OSHA ties the feed control bar to quick-stop and reverse devices through ANSI Z133.1. SafeWork NSW calls for an emergency stop that cuts the feed rollers and the disc or drum. EN 13525:2020 sets the design scope.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

The facts on this page come from the named regulators and standards bodies. It is not training and does not teach the work. The three publishers are OSHA (Safety and Health Information Bulletin 04-16-2008), SafeWork NSW (its woodchipper guide) and CEN (European standard EN 13525:2020).

OSHA: the feed control bar

The OSHA bulletin is advisory. It says it is not a standard or regulation and creates no new legal obligations. Its count: 39 employees were killed in chipper accidents from 1996 to 2005, and 78 percent of those deaths came from being caught in the chipper.

OSHA describes the feed control bar as a mechanical bar across the top and along the sides of the infeed chute that activates the feed rollers when pulled. Pushing the bar to the centre, the neutral position, stops the feed rollers. Pushing it toward the discharge spout reverses them.

The bulletin states that ANSI Z133.1-2006, Safety Requirements for Arboricultural Operations, requires chippers with a mechanical feed control bar to have quick-stop and reverse feed devices for emergencies. OSHA says many chippers in use meet this with the bar itself.

OSHA also lists other devices makers have fitted.

  • A bottom feed stop bar, from one maker, that cuts all power when 34 pounds of force is applied to the lower edge of the feed table. OSHA says the maker states it cannot be retrofitted to older models.
  • Emergency pull ropes or cables on both sides of the throat, which reverse the feed rollers when pulled. OSHA warns they may be hard to find if tangled in branches, and says they can be retrofitted.
  • A panic bar, from another maker, that stops the hydraulic system driving the feed rollers when grabbed. It is not attached to the feed control bar and has one grab bar in front and one behind.
  • Feed tray extensions, which can lengthen the infeed area by as much as four feet.
  • A flexible rubber curtain across the front of the infeed chute.

OSHA cites its machine guarding rules, 29 CFR 1910.212(a)(1) and (a)(3), and the logging standard, 29 CFR 1910.266(h)(4), which requires infeed and outfeed chutes to be guarded against contact with the disc, knives or blades where it applies.

SafeWork NSW: emergency stop and control bar

The SafeWork NSW woodchipper guide, in its section on operator control devices, says an emergency stop or shut-off device should be provided. It should immediately stop the in-feed rollers and cut power to the cutting disc or drum, which usually has a run-down time. The device should be immediately accessible to the operators and tested during the pre-start check each time the chipper is used.

The guide describes the operator control bar as setting the in-feed rollers from feed to reverse. The operating positions should be marked, showing four stages: reverse, neutral/stop, feed and reverse.

ControlSafeWork NSW wording
Side in-feed stop control barsConsideration should be given to them where the in-feed chute tray is under 600 mm high. They work like bump bars and are activated by limb or body pressure
No in-feed stop control, or tray under 600 mmThe chipper should be operated by two operators so access to the emergency stop is unhindered
Bump bar (push bar)May be retrofitted along the bottom leading edge of the chute. It should stop the rollers when body pressure pushes against it, and be painted the standard red the Work Health and Safety Regulation requires
Drop-down tableIncreases the distance between the worker and the rollers. The bump bar fits under its leading edge
Last chance stopsStop the in-feed rollers when pulled. The guide notes they may not work alone because they need the worker to pull a rope, and an entangled worker may not have a free hand
Presence-sensing safeguardQuoted from Work Health and Safety Regulation 2025 section 208(2)(d). Includes magnetic sensors worn by operators or placed on equipment, fitted and tested by the maker or a competent person

The guide adds that safety devices should be checked regularly and test results recorded, and that faults should be raised before the machine is used. It also says the safety curtain needs maintaining and replacing when cut or damaged, and can limit the operator's view of the rollers.

EN 13525:2020: design scope

EN 13525:2020, Forestry machinery - Wood chippers - Safety, was published on August 17, 2020 by CEN technical committee 144. The standards listing shows it as confirmed on December 4, 2025. It specifies safety requirements and their verification for the design and construction of self-propelled, mounted, semi-mounted and trailed wood chippers used in forestry, agriculture, horticulture and landscaping.

It applies to stationary chippers loaded by hand through a horizontal or near horizontal infeed chute, where the infeed action comes from the chipping components or from rollers or conveyors built into the chute. It excludes vertical infeed chute chippers, machines loaded only mechanically, and machines whose infeed chute has an extension table or conveyor protruding beyond the lower protective device. It does not cover engine pull starting.

The standards listing cites EN 13525:2020 under Machinery Directive 2006/42/EC.

Sources