Climbing boots and spurring boots: EN ISO 20345, 20347 and chainsaw boot EN ISO 17249
Three ISO standards cover work boots: 20345 for safety footwear, 20347 for occupational footwear and 17249 for chain saw cut resistance. No opened code names a standard for a spurring boot.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The offices are BSI and EVS for the standards, the New Zealand and New South Wales regulators and the Arboricultural Association for the codes, and the UK National Archives for the Regulation text.
The three boot standards
| Standard | Edition and status | Scope |
|---|---|---|
| EN ISO 20345, Safety footwear | EVS: 2022 edition valid from 1 Apr 2022, amendment A1 dated 1 Mar 2024. BSI: the 2004 edition, published 26 Aug 2004, withdrawn 31 Jan 2012 | Basic and additional (optional) requirements for safety footwear for general purpose |
| EN ISO 20347, Occupational footwear | EVS: 2022 edition valid from 1 Apr 2022, amendment A1 dated 1 Mar 2024. BSI: the 2004 edition, published 11 Aug 2004, withdrawn 29 Feb 2012 | Basic and additional (optional) requirements for occupational footwear for general purpose |
| EN ISO 17249:2013, Safety footwear with resistance to chain saw cutting | BSI: published 30 Nov 2013, current. EVS: valid from 9 Dec 2013, corrigendum dated 4 Mar 2014 | Requirements for safety footwear with resistance to chain saw cutting |
EVS gives the 2022 scope of both 20345 and 20347 as including mechanical risks, slip resistance, thermal risks and ergonomic behaviour. Neither covers high visibility. Both name protection against chain saw injuries among the special risks left to complementary job-related standards.
BSI recommends its 17249 version for organisations operating in or with the UK, and notes that an ISO edition is available. The older 17249 line in EVS runs from the 2004 edition of 5 January 2005 through amendment A1 of 6 March 2007.
The Regulation behind the marking
Regulation (EU) 2016/425 on personal protective equipment, in its text on legislation.gov.uk, sorts PPE into three categories of risk in Annex I. Category III covers risks that may cause very serious consequences such as death or irreversible damage to health, and its list includes cuts by hand-held chainsaws. Annex II adds that outsoles of protective footwear meant to prevent slipping must give adequate grip for the nature and state of the surface.
Footwear in the arboriculture codes
WorkSafe New Zealand's approved code says all workers in arboricultural operations shall wear footwear with safety toe caps that comply with AS/NZS 2210 Occupational protective footwear Part 1, or another standard with the same or more stringent criteria. Footwear should also support the ankles and be laced.
The New Zealand Arboricultural Association's guide to safety requirements repeats the toe cap rule. It accepts any other standard issued by member bodies of ISO or CEN with the same or relevant English-language wording.
Spurs and the footwear they attach to
The codes define and limit climbing spikes, and none names a boot standard for them. Their wording on spikes, also called spurs or gaffs, is below.
| Document | Wording on climbing spikes |
|---|---|
| SafeWork NSW, March 2026, section 4.8 | Sharpened steel spikes attached to a climber's leg. Spikes should not be worn while moving around on the ground, because they can easily puncture legs and feet. They should be used only if the tree is being removed, not for pruning |
| Industry Code of Practice, Edition 2, May 2020, 3.8.7 | Spiking is invasive and can cause significant damage to the tree. Spikes should be employed only where tree health is of negligible consequence, such as removal or aerial rescue. Spiking must be used with a personal fall protection system |
| WorkSafe New Zealand, November 2012, definitions | A climbing accessory attached to the lower leg to gain access to the tree, used with a safety strop |
| New Zealand Arboricultural Association guide, clause 40 | Climbers shall check spurs before use for fractures or cracks, misshapen, bent or loose spikes, cut or worn straps, pulled rivets and damaged or worn buckles, rings and pins. Spurs should be kept properly sharpened as per the manufacturers' recommendations |
Other personal protective equipment standards for tree work are in the PPE standards matrix.
Sources
- BSI Knowledge, BS EN ISO 20345:2004 Safety footwear, read October 16, 2026
- BSI Knowledge, BS EN ISO 20347:2004 Occupational footwear, read October 16, 2026
- BSI Knowledge, BS EN ISO 17249:2013 Safety footwear with resistance to chain saw cutting, read October 16, 2026
- EVS, EVS-EN ISO 20345:2022 catalogue entry, read October 16, 2026
- EVS, EVS-EN ISO 20347:2022 catalogue entry, read October 16, 2026
- EVS, EVS-EN ISO 17249:2013 catalogue entry, read October 16, 2026
- legislation.gov.uk, Regulation (EU) 2016/425 on personal protective equipment, read October 16, 2026
- New Zealand Arboricultural Association, Best practice guide: safety requirements for NZ arboricultural operations, Edition 3.1, 2022, read October 16, 2026
- WorkSafe New Zealand, Approved code of practice for safety and health in arboriculture, November 2012, read October 16, 2026
- SafeWork NSW, Tree works code of practice, March 2026, read October 16, 2026
- Arboricultural Association, Industry Code of Practice for Arboriculture: Tree Work at Height, Edition 2, May 2020, read October 16, 2026