Climbing gear lifespan and retirement by gear type: what OSHA, HSE, NSW, New Zealand and two makers state
Petzl gives its accessory cord a 10-year lifespan and DMM gives textile rope protectors 10 years from manufacture. OSHA calls for an inspection every workshift, and HSE asks for a weekly written record on ropes.
Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The named codes and training bodies are described here as published. It is not training and does not teach the work.
By gear type
A maker's lifespan applies to that maker's product only. Petzl's figure comes from the technical notice for its accessory cord, and DMM's from its guide for rope protectors.
| Gear type | Document | What it states |
|---|---|---|
| Climbing rope | HSE, tree work lifting equipment page | The main climbing rope and associated equipment are inspected every day by a competent person. For items with heavy wear, such as ropes, a written weekly record of inspection should be kept. |
| Climbing rope and lanyard | New Zealand Arboricultural Association, Best Practice Guide, edition 3.1, 2022 | Climbing lines, work lines and lanyards are checked for damage, cuts, abrasion and deterioration before each use and removed from service if excessive wear or damage shows. A new climbing line has a minimum breaking strain of 22 kN. |
| Lifeline | OSHA, 29 CFR 1910.140 | Lifelines must not be made of natural fibre rope. Polypropylene rope must contain an ultraviolet light inhibitor. |
| Accessory cord | Petzl, technical notice for the SEGMENT cord | Lifespan 10 years. A detailed inspection by a competent person at least once every 12 months, depending on national rules and conditions of use. |
| Rope protector | DMM, RopePro user guide | Maximum lifespan 10 years from date of manufacture for textile and plastic products. Metal products have no time limit. |
| Harness | SafeWork NSW, Tree works code of practice, March 2026 | Inspections of a work positioning harness must be carried out at least annually. |
| Harness | New Zealand Arboricultural Association, edition 3.1 | Before use, components are checked for damage, cuts, abrasion and deterioration. The complete harness is removed from service if excessive wear or damage shows or the expiry date has lapsed. |
| Lanyard | SafeWork NSW code | Webbing should be retired if there are any visible cuts. Faulty, defective or visibly worn or cut rope lanyards are permanently removed from service. |
| Connector | OSHA, 29 CFR 1910.140 | D-rings, snaphooks and carabiners must be proof tested to a minimum tensile load of 3,600 pounds (16 kN) without cracking, breaking or permanent deformation. |
| Connector | New Zealand Arboricultural Association, edition 3.1 | Carabiners and snap hooks in the climbing system are rated at or above 22 kN and are auto-locking. |
| Ascender, descender, rope grab | SafeWork NSW code | Faulty or defective equipment is removed from service until repaired and assessed as fit for use. |
Inspection cycles
OSHA requires personal fall protection systems to be inspected before initial use during each workshift for mildew, wear, damage and other deterioration. Defective components must be removed from service. The HSE page puts a daily check by a competent person on the main climbing rope, and a thorough examination by a competent person on lifting equipment that includes rigging and climbing gear.
The SafeWork NSW code has the climber inspect equipment before and after each use and keep damaged equipment out of service until a competent person assesses it. Petzl sets a detailed inspection at least every 12 months on top of the checks before and after each use.
Reasons to retire a product
Petzl lists five. The product has passed its lifespan, or it has taken a major fall or load. It fails inspection or leaves any doubt about its reliability. Its full usage history is unknown, an illegible marking for example. Or it has become obsolete through changes in legislation, standards, technique or compatibility. An exceptional event can retire a product after one use. Retired products are destroyed to prevent further use.
DMM words the same limit another way. Its lifespan is the maximum, and a product may reach the end of its life after one use, or earlier if it is damaged in transit or storage before first use. DMM lists points of its visual and tactile inspection, among them general wear, chemical contamination, corrosion, heat contamination, prolonged ultraviolet exposure, cut stitching, frayed tape and unreadable marking. Its protectors that have been used for emergency lowering or hauling are removed from service.
OSHA applies the same idea to shock loads. A system or component that has taken impact loading must be removed from service immediately. It is not used again until a competent person inspects it and finds it undamaged and safe.
Records
Petzl names the fields for its inspection form: type, model, maker contact, serial or individual number, dates of manufacture, purchase and first use, the next periodic inspection, problems and comments, and the inspector's name and signature. The New Zealand guide asks for new equipment to be entered in a logbook with the type of item, the date it enters service, the date of manufacture and any serial numbers.
Sources
- US Department of Labor, OSHA, 29 CFR 1910.140 personal fall protection systems, current text, read October 15, 2026
- Health and Safety Executive, Lifting equipment in arboriculture, read October 15, 2026
- DMM Professional, RopePro user guide, read October 15, 2026
- Petzl, technical notice for the SEGMENT accessory cord, read October 15, 2026
- New Zealand Arboricultural Association, Best Practice Guide for safety requirements in New Zealand arboricultural operations, edition 3.1, 2022, read October 15, 2026
- SafeWork NSW, Tree works code of practice, March 2026, read October 15, 2026