Climbing rope and its terminations: what the codes, the standards bodies and TCI Magazine say
Each rope end is a termination: a knot, a splice, a stitched eye or a mix. Strength, splices and wear at the ends, from the UK industry code, the New Zealand and New South Wales codes, a British Standards listing and a US trade magazine.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The UK document is the Arboricultural Association Industry Code of Practice for Arboriculture: Tree Work at Height, Edition 2 (May 2020), an industry code and not a law. Strength rules by country are covered in the guide to climbing lines and lanyards, and inspection in the guide to inspecting climbing ropes and lines. This page does not describe how to tie or splice anything.
What a termination is
The ICoP glossary defines a termination as the end of a piece of rope, which can be a knot, a splice, a stitched eye or a combination of these. The word matters because the code gives a different strength figure for rope with a termination than for rope without one.
Strength with and without a termination
| Source | New rope |
|---|---|
| ICoP clause 3.10.6.8 | New rope with a termination has a minimum breaking strength of 15 kN. New rope without a termination has 22 kN. |
| WorkSafe New Zealand code, clause 3.2.4 | A climbing line has a breaking strain of 22 kN when new and is designed for tree climbing. |
| SafeWork NSW code, clause 4.2 | No kilonewton figure. Ropes are made for industrial use and fit for the purpose and compatible with the other equipment. |
A 2021 paper in the journal Forests, from the University of Tuscia, ran 36 tensile tests on two semi-static ropes of 11 mm and 13 mm, each fitted with a Prusik or a Valdotain friction hitch. The highest load was 18.7 kN. The authors found the differences came mainly from the type of hitch rather than the type of rope. The tests covered hitches, not splices.
Who forms the splices
The ICoP says splices in climbing rope are formed only by the manufacturer, or with the manufacturer's consent, against validated performance criteria and subject to independent verification (clause 3.10.6.8). Under the WorkSafe NZ code, climbing lines are free of joining splices or knots, and spliced eyes or end splices follow the rope maker's instructions (clause 3.2.4). The ICoP clause is about who forms a splice. The NZ clause is about splices and knots that join lengths of line. The NZ code adds that a knot can take away up to half of the breaking strength of a rope. It also sets the safe working load of a climbing rope and its equipment at 10 percent of the breaking or tensile strength.
Static and dynamic rope
The SafeWork NSW code, clause 4.2, says static ropes are for access only and dynamic ropes are chosen for moving across and working in the tree. A rope made unsafe for any reason, damage and wear among them, should be taken out of use. The ICoP, in its standards list, names BS EN 892 for dynamic mountaineering ropes and BS EN 1891 for low stretch kernmantel ropes. The British Standards Institution lists BS EN 1891:1998 as published on September 15, 1998 and as "Current, Under Review", titled Personal protective equipment for the prevention of falls from a height: Low stretch kernmantel ropes. Its descriptors include elongation, marking, instructions for use and safety lines.
Rope names in a trade magazine
Tree Care Industry Magazine, the publication of the Tree Care Industry Association, ran an article on inspecting gear on June 1, 2022. It lists rope constructions as 3-strand, 12-strand, 16-strand, 24-strand, 32-strand, 48-strand, hollow-braid, single-braid, double-braid and kernmantle, and calls the inspection criteria similar for all of these. The author names work-positioning lanyards and rope ends near a splice as the items that most often come up for retirement. Climbers tend to keep a rope longer than its condition allows, he writes, because a splice is a useful feature in their climbing systems. Irregular diameter can show that a rope was overloaded at some point. How many strands can be cut before retirement depends on the maker and the construction.
Care at the ends
The ICoP, in its section on inspection and maintenance, says routine maintenance may include minor work such as resealing the rope ends, milking ropes and trimming broken fibres. All of these must be done judiciously to avoid safety-critical damage, and a footnote says maintenance follows the maker's information, because actions outside the maker's authorisation could count as alteration or modification.
Gaps in the sources
None of the documents sets rules for how many strands a rope has or how a rope is built. SafeWork NSW prints no breaking strength figure for rope in section 4, and the magazine article is the opinion of its author and not a code.
The SafeWork NSW Tree works code of practice is licensed under Creative Commons Attribution 4.0. WorkSafe New Zealand is credited as the source of its code. The wording is ours.
Sources
- Arboricultural Association, Industry Code of Practice for Arboriculture: Tree Work at Height, Edition 2, May 2020, read October 9, 2026
- WorkSafe New Zealand, Safety and health in arboriculture approved code of practice, read October 9, 2026
- SafeWork NSW, Tree works code of practice, March 2026, read October 9, 2026
- Tree Care Industry Magazine, PPE Part 2: Why We Inspect Our Gear, June 1, 2022, read October 9, 2026
- BSI Knowledge, BS EN 1891:1998 low stretch kernmantel ropes, read October 9, 2026
- Bianchini et al., Tensile Strength of Ropes and Friction Hitch Used in Tree Climbing Work, Forests 2021, 12, 1457, October 26, 2021, read October 16, 2026