ArbNation Join free

Climbing words by code: anchor, anchorage, tie-in point, strop, lanyard and flip line across the UK, NSW, NZ and Alberta

The climbing codes do not share one vocabulary. WorkSafe New Zealand calls a lanyard a strop or flip line, the UK code keeps strop for slings, and no code defines a tie-in point.

Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.

The named codes are described here as published. It is not training and does not teach the work. Credits: SafeWork NSW text is summarised from the Tree works code of practice (March 2026), copyright State of New South Wales (SafeWork NSW), licensed under Creative Commons Attribution 4.0; changes were made, because the text is summarised and reworded. WorkSafe New Zealand material is summarised from its Approved Code of Practice for Safety and Health in Arboriculture, with the source acknowledged. HSE text is adapted from HSE pages published under the Open Government Licence v3.0.

Anchor, anchor point and anchorage

Anchor words by code
CodeWording
UK, Arboricultural Association ICoP (2020)Defines three terms. An anchor is a structural place, fixing or fixture to which a safety line or anchorage device is attached. An anchor point is a point of attachment for personal fall protection systems or anchor devices. An anchor device is a component or assembly that connects to either. Its section on Anchorage covers artificial, temporary anchor points such as tape slings and cambium or pulley savers, with a minimum breaking strength of at least 18 kN.
UK, HSEWants the system attached, where possible, to two anchor points that carry the load, each strong enough for the climber, work equipment and foreseeable loading.
New South Wales, SafeWork NSW (2026)Defines an anchor point as a fork of two branches, or of a branch and the trunk, that a climber can safely use for the rope (natural). It can also be a device installed in a tree, such as a pulley and sling assembly (artificial). The word anchorage does not appear.
New Zealand, WorkSafeUses anchor point throughout the climbing section and does not use anchorage. The climber's weight and equipment, and a potential rescuer's, must be carried by the anchor points. A second anchor point is needed when cutting.
Alberta, Part 41Uses anchor for industrial rope access (anchor strength, at least 16 kilonewtons per worker) and anchorage for the safety and working lines (a separate anchorage connection). The headings for non-industrial rope access say anchorage strength.

Tie-in point and TIP

None of the five codes defines a tie-in point or TIP. The WorkSafe New Zealand code says arborists shall be tied in or secured to the tree while ascending and remain tied in until they are back on the ground. In the United States, a first-person account in Tree Care Industry Magazine uses TIP and spells it out once, in brackets, as tie-in point.

Strop, lanyard and flip line

Lanyard words by code
CodeWording
UK, Arboricultural Association ICoP (2020)A lanyard is a short, adjustable system that gives a means of connection to an anchor. Slings and strops are textile components in varied configurations, sizes and lengths.
New South Wales, SafeWork NSW (2026)Section 4.4 pairs the work positioning harness with adjustable lanyards or pole straps, and section 4.5 covers the lanyards. The glossary defines a tool lanyard or tool strop as rope or webbing that attaches the climber's tools to the harness.
New Zealand, WorkSafeThe glossary entry safety lanyard reads "strop/flip line": an adjustable rope or strop used as a work positioning aid. A work positioning lanyard is listed as the same thing. A tool strop is a short line that secures tools while aloft. The code uses flip line in that entry and in a rule on strops or flip lines containing metal near power lines.

So a strop is a climber's lanyard in New Zealand, a tool line in New South Wales and a sling in the United Kingdom. The ICoP, HSE and SafeWork NSW texts do not use the term flip line.

Friction device and climbing device

Device words by code
CodeWording
New Zealand, WorkSafeA friction device is an alloy or metal device that controls friction on a line. Used to secure a climber to the climbing line, it permits controlled ascent, descent and work positioning, and is rated to at least 22 kN. A friction hitch does the same job in synthetic fibre.
UK, Arboricultural Association ICoP (2020)Defines hitch (friction) as the term for knots and hitches that control ascent or descent or hold position on the rope and self-lock when released. It mentions friction devices alongside ropes and pulleys.
UK, HSENames the friction knot as part of changeover climbing, with a harness and climbing line.
New South Wales, SafeWork NSW (2026)Has no entry for friction device. A climbing device is the attachment between the harness and the ropes that lets the climber ascend or descend. A descender is a knot or mechanical friction device used with a rope for controlled descent.

More climbing terms are defined in the climbing glossary.

Sources