Corded electric chainsaws and pole saws: IEC scope, the GFCI rule and a 2025 recall
IEC 62841-4-1 covers electric chain saws for one person and excludes tree-service saws and pole-mounted pruners. Its parent standard sets limits of 250 V and 3,700 W. CPSC recalled corded saws in July 2025.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here.
IEC 62841-4-1: electric chain saws
IEC 62841-4-1, edition 1.1 (2024-10, corrected 2025-06), is the electric chain saw part of the IEC 62841 series. Its scope clause says it applies to chain saws for cutting wood that are designed for use by one person. The chain saws it covers are operated with the right hand on the rear handle and the left hand on the front handle.
The same clause lists what it does not cover:
- chain saws designed for use with a guide-plate and riving knife, or used on a support, or as a stationary or transportable machine;
- chain saws for tree service as defined in ISO 11681-2;
- pole-mounted pruners.
A note says pole-mounted pruners will be covered by a future part of IEC 62841. A corded pole saw therefore sits outside this part, and so does a corded tree-service saw. The standard defines a chain saw as a machine with an integrated unit of handles, motor, guide bar and saw chain, supported with two hands. It also defines a bar tip guard, a chain catcher, and a chain brake that is activated manually or non-manually when kickback occurs.
IEC 62841-1: the general limits
Part 1 of the series, IEC 62841-1:2014+AMD1:2025, deals with the safety of electric motor-operated or magnetically driven hand-held tools, transportable tools, and lawn and garden machinery. The catalogue page for the consolidated version gives the limits. Rated voltage is not more than 250 V for single-phase a.c. or d.c. tools and 480 V for three-phase a.c. tools. Rated input is not more than 3,700 W. Battery tools follow separate limits in its Annexes K and L.
Part 1 also lists changes from the earlier standards it replaces. The leakage current test and electric strength test moved to Annexes C and D, and requirements for switches were revised and moved into Clause 23. Part 1 is scheduled to replace parts of IEC 60745-1, IEC 61029-1 and IEC 60335-1 only for lawn and garden machinery.
Ground-fault protection in OSHA's construction rule
OSHA's electrical rule for construction, 29 CFR 1926.404(b)(1), has employers use either ground fault circuit interrupters or an assured equipment grounding conductor program to protect employees on construction sites. The GFCI paragraph covers all 120-volt, single-phase, 15- and 20-ampere receptacle outlets on construction sites that are not part of the permanent wiring of the building and are in use by employees. A two-wire portable or vehicle-mounted generator rated not more than 5 kW, with insulated circuit conductors, is excepted.
That rule is limited to construction sites. The HSE chainsaw leaflet INDG317 does not mention residual current devices or GFCIs.
The July 2025 CPSC recall
The US Consumer Product Safety Commission announced recall 25-371 on July 3, 2025 for corded electric chainsaws and pole saws from Positec Tool Corporation of Charlotte, North Carolina. About 49,000 units were sold in the United States and about 3,000 in Canada. The notice says the main switch can fail and keep the saw running after the trigger is released, which creates a laceration hazard. No incidents were reported.
The recalled products were a 14 inch corded chainsaw sold in three versions and an 8 amp corded pole saw. They were sold at national retail stores and online from September 2024 through March 2025. The remedy in the notice is replacement: consumers stop using the saw, contact the firm for a prepaid return label and, if needed, a new box, and the firm sends a free replacement. The serial ranges and the Health Canada notice are on the recall entry for these saws.
Battery-powered saws have a different set of rules and recalls, covered in battery saws and lithium-ion batteries.
Sources
- IEC, IEC 62841-4-1:2017+AMD1:2024 edition 1.1, preview (scope, definitions), read October 16, 2026
- IEC webstore, IEC 62841-1:2014+AMD1:2025 CSV consolidated version, catalogue page, read October 16, 2026
- US CPSC, Positec recalls electric corded chainsaws and pole saws due to laceration hazard, recall 25-371, July 3, 2025, read October 16, 2026
- US OSHA, 29 CFR 1926.404 Wiring design and protection, (b)(1) (eCFR, current text), read October 16, 2026
- UK HSE, Chainsaws at work, INDG317(rev2), published 01/13, read October 16, 2026