Drop zones and exclusion zones in tree work: the distances and wording each regulator uses
SafeWork NSW, WorkSafe New Zealand, HSE, WorkSafeBC, OSHA and the UK industry code each word the zone duties differently. Only some print a distance: two tree-lengths in New Zealand and British Columbia, 1.5 times a section's length in New South Wales.
Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The wording below is what the named codes and regulators publish. It is not training and does not teach the work.
The wording by regulator
| Regulator and document | Terms, duties and distances |
|---|---|
| SafeWork NSW, Tree works code of practice (commenced March 27, 2026) | Defines an exclusion zone as a large area that persons who are not workers are kept out of. Defines a drop zone as the area set aside for the whole tree to land when felling, or for branches, limbs or trunk sections to be put down after cutting. Workers must not enter the drop zone while a tree or material is being felled or dropped. No fixed distance: the size and boundaries come from a risk assessment. For sectional felling the drop zone should be a minimum of 1.5 times the length of the section. |
| WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture (November 2012) | Uses neither term. People not directly helping with a felling stay at least two tree-lengths from the tree being felled. No machine works within two tree-lengths of a felling unless it is helping, under supervision, to bring the tree down. No person moves forward within two tree-lengths of the intended fall direction of a hung-up or cut-up tree. |
| HSE, Great Britain, tree work case studies page | Defines a danger zone as an area to the front and rear of a tree where the tree is most likely to fall during or after the sink and felling cuts. No distance is printed. HSE refers to Figure 1 in Appendix 1, AFAG302 Basic chainsaw felling and manual takedown, for an illustration. |
| WorkSafeBC, OHS Regulation Part 26, Forestry Operations | Defines the active falling area as the area within a 2 tree-length radius of where a faller or mechanized falling equipment is located and equipped to fall timber. Only a worker with duties tied to the falling may enter it. A worker entering notifies the faller or bucker and waits for word that it is safe. |
| OSHA, Hurricane eMatrix activity sheet on tree trimming | For trimming, workers not needed in the area stay at least 20 feet beyond expected drop zones. For felling, adjacent occupied work areas are at least two tree lengths from the tree being felled, more if the tree might roll or slide. |
| Arboricultural Association, Industry Code of Practice for Arboriculture: Tree Work at Height (edition 2, May 2020) | Names two zones. The drop zone is where materials are anticipated to fall and people or property would be at significant risk. The work zone is where hazards could be met or created, and the work team but not the public may enter it. No distance is given: the size of each zone is assessed and decided individually. |
New South Wales: how the zone is sized
The SafeWork NSW code ties the zones to the WHS Regulation duty to manage the risk of an object falling on a person. Where the fall cannot be prevented, the risk is minimised with adequate protection and a safe system of work, which may include an exclusion zone persons are prohibited from entering.
The code lists what a drop zone assessment weighs. That is the size of the work area, the length, size and shape of the material, and sloped or uneven ground that lets material roll or slide. It also weighs deflection off branches, roots, structures or hard surfaces, and exclusion distances wide enough for unexpected movement. One site may have several exclusion zones, for pedestrian access, vehicle access and plant operation.
On sectional felling the code adds that any change to the drop, felling or exclusion zone must be communicated and acknowledged by the ground workers. For felling with powered plant, all ground workers must remain outside the drop zone once cutting begins.
The UK industry code and the Association guide
The Industry Code of Practice says the extent of the drop zone must be clear to anyone in the work zone, through signs, site features such as the canopy dripline, or supervision by operators. The drop zone may move many times during a task, and the controls are communicated to the whole team as it changes. A change to any zone follows a reassessment of the factors that set the original size.
The same code lists identifying the drop zone among the abilities operators need for dismantling, rigging and platform work. The Association's Safety Guide 3, on rigging and dismantling (December 2021), carries the same duty as a planning checklist item: whether drop, work and exclusion zones have been identified and all operators know them.
Where OSHA's logging standard stands
The OSHA logging standard, 1910.266, does not use the term drop zone. The eMatrix sheet above carries the wording for tree work in a hurricane response, and OSHA states that the matrix does not alter or determine compliance responsibilities in OSHA standards.
Credit
Wording drawn from the SafeWork NSW code is used under CC BY 4.0. Wording drawn from HSE is used under the Open Government Licence v3.0. WorkSafe New Zealand material is reproduced with acknowledgement.
Sources
- SafeWork NSW, Tree works code of practice (commenced March 27, 2026), section 3.5 and part 9, read October 15, 2026
- Arboricultural Association, Industry Code of Practice for Arboriculture: Tree Work at Height, edition 2, May 2020, read October 15, 2026
- Arboricultural Association, Safety Guide 3: Rigging and Dismantling, December 2021, read October 15, 2026
- WorkSafeBC, OHS Regulation Part 26, Forestry Operations, read October 15, 2026
- HSE, Tree work: case studies and terms, read October 15, 2026
- WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture, November 2012, read October 15, 2026
- OSHA, Hurricane eMatrix activity sheet: Tree Trimming, read October 15, 2026