Dropped objects and tool tethering: ANSI/ISEA 121 and the OSHA falling-object rules
ANSI/ISEA 121-2018 covers equipment that tethers or contains tools against falling from height. OSHA's falling-object rules name hard hats, toeboards, screens, canopy structures and barricades, and none of them mentions tethers.
Checked against the sources at the bottom of this page on October 18, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The standard's scope comes from ISEA, the trade association that developed it. The rules come from OSHA's regulations on falling-object protection, 29 CFR 1926.501(c) for construction and 29 CFR 1910.28(c) and 1910.29(k) for general industry. OSHA's tree care page adds how the general industry standards reach tree care.
ANSI/ISEA 121-2018
ISEA, the trade association for manufacturers of dropped object prevention solutions, developed ANSI/ISEA 121-2018, the American National Standard for Dropped Object Prevention Solutions. It was written with ISEA's Dropped Object Prevention Solutions Product Group and industry stakeholders. ISEA calls it the first standard to address equipment used to tether or contain hand tools, components, structure and other objects from falling in at-heights applications.
The standard sets design, testing and performance criteria for active systems that prevent dropped objects in the workplace. ISEA lists four categories of equipment: anchor attachments, tool attachments, tool tethers and containers. The standard is limited to that scope. ISEA states that use of the equipment may differ between manufacturers and employers.
ISEA contrasts these active controls with protective measures. Hard hats minimise the effects of a strike only after an object has fallen. Netting and toeboards also reduce the risk, but ISEA says they face challenges and do not entirely prevent incidents. Active controls that tie off or contain objects at height are, in ISEA's words, a rapidly growing practice. ISEA states that struck-by falling objects kill hundreds of people each year and injure tens of thousands.
Falling-object rules in OSHA regulations
| Item | 29 CFR 1926.501(c), construction | 29 CFR 1910.28(c), general industry |
|---|---|---|
| Trigger | An employee is exposed to falling objects | An employee is exposed to falling objects |
| Head protection | Each employee wears a hard hat | Each employee wears head protection that meets subpart I |
| Further protection | One of three measures | One or more of three measures |
| Measure 1 | Toeboards, screens or guardrail systems to keep objects from falling from higher levels | Toeboards, screens or guardrail systems to keep objects from falling to a lower level |
| Measure 2 | A canopy structure, with potential fall objects kept far enough from the edge | Erected canopy structures, with potential falling objects kept far enough from an edge, hole or opening |
| Measure 3 | Barricade the area where objects could fall, prohibit entry and keep objects away from the edge | Barricade the area into which objects could fall, prohibit entry and keep objects away from an edge or opening |
Section 1910.29(k) sets criteria for the general industry measures. A toeboard used for falling object protection has a minimum vertical height of 3.5 inches, measured from its top edge to the walking-working surface. It must withstand a force of at least 50 pounds applied downward or outward at any point. Where tools, equipment or materials are piled higher than the toeboard, paneling or screening goes from the toeboard to the midrail, and to the top rail if they are piled higher than the midrail. Canopies must be strong enough to prevent collapse and penetration by falling objects.
Sections 1926.501, 1910.28 and 1910.29 contain no wording on tool tethers or on tying off or containing tools. The only lanyard among them is the 18-inch rest lanyard on a body harness for certain ladder climbing in 1910.28. Their measures act at the edge or below it: barriers, screens, canopy structures and keep-out zones. ISEA describes ANSI/ISEA 121 as covering active controls, which tie off or contain the object itself.
How OSHA treats tree care
OSHA's tree care industry page states that tree care hazards are addressed in specific OSHA standards for recordkeeping and general industry. It states that the tree care industry must comply with all the general industry standards in 29 CFR 1910. Its list of standards includes 1910.29, the criteria for fall protection systems and falling object protection, and 1910.30 on training.
OSHA's tree care pages also list a publication, Tree Care Work: Falls and Falling Object Hazards. The list of standards on the tree care page names general industry sections, not 29 CFR 1926.501. Drop zones for tree work are covered in the guide to drop zones and exclusion zones.
Sources
- International Safety Equipment Association, Dropped Object Prevention Solutions product group page (ANSI/ISEA 121-2018 scope), read October 16, 2026
- US Government, 29 CFR 1926.501 Duty to have fall protection, paragraph (c), eCFR, read October 16, 2026
- US Government, 29 CFR 1910.28 Duty to have fall protection and falling object protection, eCFR, read October 16, 2026
- US Government, 29 CFR 1910.29 Fall protection systems and falling object protection, criteria and practices, paragraph (k), eCFR, read October 16, 2026
- OSHA, Tree Care Industry: Standards, read October 16, 2026
- OSHA, Tree Care Industry: Additional Resources, read October 18, 2026