Emission control labels on saws: what 40 CFR 1054.135 puts on the label, and CARB's rule
Federal rule 40 CFR 1054.135 sets the heading EMISSION CONTROL INFORMATION and a compliance period in hours on an engine's label. California requires small off-road engines to be certified and labelled for sale.
Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The label wording below is from 40 CFR 1054.135, the EPA rule on labelling and identifying engines under Part 1054, the control of emissions from new, small nonroad spark-ignition engines and equipment. The rule text on that section applies to engine manufacturers.
Where the label rule sits
EPA's rule page for the Phase 2 handheld standards covers new nonroad spark-ignition handheld engines at or below 19 kilowatts (25 horsepower). It names chainsaws among the handheld lawn and garden uses, with the standards phased in beginning with the 2002 model year. The final rule was published April 25, 2000.
Section 1054.135 is headed "How must I label and identify the engines I produce?" It sits in Subpart B of Part 1054, Emission Standards and Related Requirements.
The label itself
Paragraph (b) of the section calls for a permanent, legible label on each engine at the time of manufacture. The label is attached in one piece so it is not removable without being destroyed or defaced. It is secured to a part of the engine needed for normal operation and not normally requiring replacement. It is durable and readable for the engine's entire life, and written in English.
Paragraph (a) adds a unique identification number, permanently affixed, engraved or stamped on the engine in a legible way.
The label content in paragraph (c)
| Paragraph | Content |
|---|---|
| (c)(1) | The heading "EMISSION CONTROL INFORMATION" |
| (c)(2) | The manufacturer's full corporate name and trademark |
| (c)(3) | EPA's standardized designation for the emission family, and subfamily where applicable |
| (c)(4) | "EMISSION COMPLIANCE PERIOD = [applicable useful life period] HOURS", based on the useful life requirements in section 1054.107 |
| (c)(5) | The engine's displacement in cubic centimeters, which may be omitted if every engine in the family has the same per-cylinder and total displacement |
| (c)(6) | The date of manufacture as day (optional), month and year, which may be stamped elsewhere on the engine |
| (c)(7) | The emission control system, in the terms and abbreviations of 40 CFR 1068.45, which may go in the owners manual if the label has no room |
| (c)(8) | One of two statements, shown below |
The label must conform to these specifications without exception.
The compliance statement
Paragraph (c)(8) gives two statements. An integrated equipment manufacturer certifying engines for exhaust emissions and meeting the evaporative requirements of 40 CFR part 1060 states "THIS ENGINE MEETS U.S. EPA EXH/EVP REGS FOR [MODEL YEAR]". In all other cases the statement is "THIS ENGINE MEETS U.S. EPA EXH REGS FOR [MODEL YEAR]".
On the compliance period, paragraph (c)(4) lets the manufacturer add the descriptive terms of section 1054.107(a). It also allows the term Heavy Commercial for nonhandheld engines where a longer useful life is established.
Optional content and duplicate labels
Paragraph (d) lists information that may be on the label or in the owners manual: tune-up specifications and adjustments, the altitude for an altitude kit, and the fuel type with any fuel and lubricant requirements. Paragraph (e) allows other standards the engine meets or does not meet, such as California standards, and features against counterfeit labels, for example the unique identification number.
Under paragraph (g), if others install the engine in a way that obscures the label so it cannot be read during normal maintenance, they add a duplicate label on the equipment. The rule refers to 40 CFR 1068.105. The date of manufacture may be left off the duplicate.
The section was published at 73 FR 59259 on October 8, 2008, and amended at 80 FR 9114 on February 19, 2015 and 86 FR 34518 on June 29, 2021.
The CARB rule
The California Air Resources Board's small off-road engine FAQ says its regulations apply to manufacturers, sellers, retailers and distributors of new spark-ignition engines of 25 horsepower or less, and require that they certify and label those engines. The regulations require equipment to be certified and labelled for sale in California.
The FAQ lists chainsaws under 45 cc among the equipment included. The regulations do not affect equipment already sold and in use. Battery-electric equipment need not be certified. Engines and equipment primarily used for commercial construction or commercial farming are not regulated by this rule pursuant to federal law.
The FAQ prints no wording for the California label. The guide to chainsaw emissions rules by jurisdiction holds the wider picture.
Sources
- US eCFR via Cornell LII, 40 CFR 1054.135 How must I label and identify the engines I produce, read October 19, 2026
- US EPA, Final Rule for Phase 2 Emission Standards for New Nonroad Spark-Ignition Handheld Engines, rule page, read October 19, 2026
- California Air Resources Board, Small Off-Road Engine Regulations Frequently Asked Questions, read October 19, 2026