ArbNation Join free

EN 12841 type A, B and C rope adjustment devices: what each type is and which codes cite them

EN 12841 covers three types of rope adjustment device: type A backup devices, type B working line ascenders and type C working line descenders. Of the UK, New South Wales and New Zealand codes checked, only the UK industry code lists it.

Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The named codes and training bodies are described here as published. It is not training and does not teach the work.

The standard

BSI lists BS EN 12841:2024 as Personal fall protection equipment. Rope access systems. Rope adjustment devices, published on 31 March 2024. BSI gives its status as current, under review, and says the British text is identical to EN 12841. The standard comes from BSI committee PH/5 and sits under ICS code 13.340.60, protection against falling and slipping. BSI's page is a catalogue entry, so it shows the title and descriptors but not the scope text.

The three types

IRATA, the rope access trade body, described the standard in October 2020 when the draft of the revision went out for public consultation. IRATA says EN 12841 applies to rope adjustment devices intended for use in rope access systems. It sets requirements, test methods, marking and the maker's instructions for three types of device.

EN 12841 device types as IRATA describes them
TypeDevice
Type ASafety line adjustment device, commonly known as a backup device
Type BWorking line ascender
Type CWorking line descender

The 2020 draft revised the 2006 version of the standard. IRATA points to an appendix explaining the reasons for the changes and another listing the significant ones, and its comment period closed on 26 October 2020.

Which tree work codes cite it

The Arboricultural Association's Industry Code of Practice for tree work at height, second edition of May 2020, lists BS EN 12841 in its reference list of standards. The HSE page, the SafeWork NSW code and the WorkSafe New Zealand code do not cite it.

EN 12841 in the tree work codes
CodeCites EN 12841What it names for climbing equipment
Arboricultural Association ICoP, United Kingdom, May 2020Yes, in its standards listLists BS EN standards for harnesses, connectors, ropes, anchors and rope adjustment devices, plus ISO 22159 for descending devices
HSE tree climbing page, United KingdomNoNames no equipment standard on the page
SafeWork NSW tree works code, March 2026NoAS/NZS 1891.1:2020, AS/NZS 1891.4:2025 and AS/NZS ISO 22846.1:2020
WorkSafe New Zealand arboriculture code, November 2012NoClimbing equipment to meet applicable safety standards, harnesses to AS/NZS 1891 or equivalent

No code opened for the United States, Canada or Ireland is covered here, so this table makes no statement about them.

Device wording in the codes

The ICoP gives rope adjustment devices their own heading, next to ascending devices, backup devices and descending devices. It defines a rope adjustment device as one applied at a mid-point, or threaded on to the end of a component such as a lanyard, to introduce or remove slack. It does not label any of its device headings as type A, B or C.

The ICoP says a backup device must keep any fall distance as short as possible, be configured so it cannot be inadvertently disconnected from the line, and be compatible with the rope type and diameter. Its glossary defines an ascender as a device that slides when advanced up a rope and grips when loaded the other way.

The SafeWork NSW code has a section on mechanical ascenders, descenders and rope grabs. It lists points to consider: compatibility with the rope, self-locking, an automatic braking function on descent devices, and a backup on the main line when a mechanical ascender is used. The WorkSafe New Zealand code defines an ascender in the same terms as the ICoP and names no device standard.

Sources