EN 12841 types A, B and C explained: rope adjustment device categories in the BSI record and maker papers
EN 12841 sorts rope adjustment devices into type A backup devices, type B ascenders and type C descenders. A label can carry one letter or a pair, such as B/C, and Edelrid's summary lists the marking a maker must print.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The named codes and training bodies are described here as published. It is not training and does not teach the work.
The standard
BSI Knowledge lists BS EN 12841:2024, Personal fall protection equipment. Rope access systems. Rope adjustment devices, published on 31 March 2024. Its status is current and under review, and the British text is identical to EN 12841. The record sits under committee PH/5 and ICS codes 13.340.60 and 13.340.99. Its descriptors include performance testing, marking, instructions for use, safety lines, fall arrest systems and locking and locating devices. The catalogue page shows no scope text. A DIN project page lists EN 12841:2024/prA1:2026 as a draft amendment to the 2024 edition, begun on August 29, 2025 under CEN/TC 160/WG 3.
The three types
Edelrid prints a simplified summary of the standard, based on the 2006 edition, and states it does not hold the full details. The summary defines the types, with Edelrid's own example products in the original.
| Type | Device | Definition |
|---|---|---|
| A | Rope adjustment device for safety lines (guided type fall arrester, back-up device) | Follows the user's changes of position or allows adjustment on the safety line, and locks to the line automatically when a static or dynamic load is applied, in a fall for example |
| B | Ascending device for working lines (ascender) | Manually operated. Locks under load in one direction and slides freely in the opposite direction |
| C | Descending device for working lines (descender) | Manually operated, friction-based. Lets the user descend in a controlled way and stop at a point without holding on by hand |
Test figures by type
Edelrid's summary gives the tests that apply to each type and their figures. All figures below are the summary's, from the 2006 text.
| Test | Type A | Type B | Type C |
|---|---|---|---|
| Static strength, held 3 minutes | 15 kN | 4 kN | 12 kN |
| Minimum working strength, force held 3 minutes | Rated load plus 1 kN | 4 kN | 3 kN |
| Slippage allowed in that test | Under 100 mm | Under 100 mm | Under 300 mm |
| Dynamic test | Mass of at least 100 kg or the rated load, braking force 6 kN at most, braking distance 2000 mm at most | None listed | None listed |
| Descent speed | None listed | None listed | Tested on a 50 m rope; operating parts not above 48 degrees C |
A separate capacity reserve test applies to all three types. The device hangs 1000 mm below the anchor, the rated load or at least 100 kg is raised 2000 mm and dropped, and the device may not release the line or brake over 2000 mm. The mass is then raised to 3 kN and held for 3 minutes.
What a type letter on a label means
Edelrid lists the information a maker must supply on the product. It covers the maker, EN 12841, model, batch number, year of manufacture and smallest and largest rope diameter. It also covers a reference to the user manual, the type of device, the anchor line diameter, the maximum rated load and the type of anchor line, such as EN 1891 type A. The list adds the correct orientation in normal use and the CE mark with a four-digit number.
The type entry is one of A, B, C, A/B, A/C or B/C. A label reading C marks a descender, and B/C marks a device built to both the ascender and descender definitions.
A device certified as both B and C
Petzl's technical page on the certification of its ZIGZAG shows the pairing. The device was certified under the relevant articles of EN 12841:2006 and Regulation 2016/425. Petzl states that no rule applies exactly to a device like it and that EN 12841, which distinguishes three types of rope adjustment device, comes closest. The ZIGZAG works as both a type B rope clamp and a type C descender, so tests from both types were used. The ropes used were EN 1891 type A in 11.5 mm and 13 mm.
Sources
- BSI Knowledge, BS EN 12841:2024 catalogue record, read October 15, 2026
- Edelrid, EN 12841 personal fall protection equipment, rope adjustment devices, summary of the standard, read October 15, 2026
- Petzl, Zertifizierung des ZIGZAG (Tech Tips), read October 15, 2026
- DIN, project page for EN 12841:2024/prA1:2026 rope adjustment devices, read October 16, 2026