ArbNation Join free

Energy-absorbing lanyards in tree work: absorber standards and code free-fall limits

New South Wales prints 600 mm as the free-fall limit for work positioning, New Zealand prints 0.5 m of slack, and OSHA prints 6 feet for fall arrest. BS EN 355 and ANSI/ASSP Z359.13 cover the absorbers.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

The named codes and standards bodies are described here as published. It is not training and does not teach the work.

Standards that cover absorbers

StandardListed as
BS EN 355:2002Personal protective equipment against falls from a height: energy absorbers. BSI gives the publication date as July 4, 2002 and the status as current.
ANSI/ASSP Z359.13Energy absorbers and energy absorbing lanyards, in the Z359 family listed by the American Society of Safety Professionals.

The BSI scope covers requirements, test methods, marking, maker information and packaging. Absorbers under EN 355 are used built into a lanyard, an anchor line or a full body harness, or alongside one of them.

BSI adds that an absorber and lanyard together form a sub-system of the fall arrest systems in EN 363, when combined with a full body harness to EN 361. Fall arresters sit in EN 353-1, EN 353-2 and EN 360.

The UK Industry Code of Practice for Arboriculture: Tree Work at Height (Edition 2, May 2020) lists BS EN 355 in its standards table. Its lanyard clause, 3.10.6.10, does not mention absorbers.

Free fall in the tree work codes

CodeWording
SafeWork NSW, Tree works code of practice, March 2026, section 4.4A work positioning harness is limited to situations that may result in a restrained fall or a limited free fall. It should not be used if there is a risk of a free fall greater than 600 mm.
SafeWork NSW, section 4.9When a climbing rope is part of the fall prevention system, the rope is kept taut to limit fall distance to 600 mm or less.
WorkSafe New Zealand, approved code of practice, November 2012, section 3.2There is to be no more than 0.5 metres of slack in the climbing line at any time.
WorkSafe New Zealand, section 3.2.6The code describes fall arrest harnesses as the type that arrests a worker's fall. The attachment to the anchor usually includes some type of energy absorbing device, reached through the chest or dorsal point.
ICoP, clause 3.10.6.10An adjustable lanyard is preferred in the most common use because it minimises slack, and so the distance and consequences of a fall. The code prints no free-fall distance.

The New Zealand code also says "elevating work platforms" are provided with a point of attachment to secure a fall-arrest harness with a shock-absorbing lanyard.

OSHA 29 CFR 1910.140

The US federal standard sets criteria for personal fall arrest systems in paragraph (d). The system limits the maximum arresting force on the employee to 1,800 pounds (8 kN). It limits the deceleration distance to 3.5 feet (1.1 m).

It must withstand twice the impact energy of a free fall of 6 feet (1.8 m), or the free fall the system permits. Systems are rigged so the employee cannot free fall more than 6 feet (1.8 m) or hit a lower level.

A longer free fall is allowed where the manufacturer designed and tested the system for it and the 1,800 pound (8 kN) force is not exceeded. Body belts are prohibited as part of a personal fall arrest system.

The same standard allows a pre-sternal attachment point if free fall is limited to 2 feet (0.6 m) or less.

Figures that differ

The 600 mm figure comes from the New South Wales tree code and applies to work positioning. The 0.5 m figure is the New Zealand tree code's limit on slack in the climbing line. The 6 foot figure comes from a US workplace standard for fall arrest systems. The three documents cover different systems.

Sources