Equipment standards named by regulators: Alberta, Ireland and Great Britain tree-work rules
Alberta's OHS Code names CSA, ANSI, ASTM, CEN and NFPA standards for eyewear, footwear, headwear and work positioning harnesses. Ireland's HSA and Britain's HSE name EN standards for chain saw and aerial PPE.
Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. It extends the PPE standards matrix. Three regulators are added. Alberta's Occupational Health and Safety Code (Alberta Regulation 191/2021, Parts 18 and 39) comes first. Next are two Health and Safety Authority (HSA) chain saw documents for Ireland. The Health and Safety Executive (HSE) page on PPE for aerial tree work in Great Britain comes last.
Alberta, Occupational Health and Safety Code
Part 18 covers personal protective equipment. Section 228 puts a duty on the employer to see that workers wear PPE correct for the hazard when the hazard assessment shows the need, and on the worker to wear and inspect it. The sections that name standards are 229 for eyes, 233 for feet and 234 for heads.
| Item | Standard the Code names |
|---|---|
| Eye and face protectors (s. 229) | CSA Z94.3-15. Prescription frames may meet ANSI Z87.1-2003, and treated safety glass lenses may meet ANSI Z87.1-2003 or Z87.1-1989 where plastic lenses are impracticable and there is no impact danger |
| Protective footwear (s. 233), where the hazard assessment calls for toe protection, a puncture resistant sole, metatarsal, electrical or chainsaw protection | CSA Z195-14, or ASTM F2413-05 for footwear made on or after March 31, 2023 |
| Protective headwear (s. 234), where lateral impact to the head is a significant possibility | CAN/CSA Z94.1-15, or ANSI Z89.1-2003 Type II, for headwear made on or after March 31, 2023 |
| Protective headwear (s. 234), where lateral impact is unlikely | CAN/CSA Z94.1-05, or ANSI Z89.1-2003, for headwear made on or after July 1, 2009 |
| Flame resistant outerwear (s. 232), where a worker may meet a flash fire or electrical equipment flashover | No standard named |
| Limb and body protection (s. 242) | No standard named; the equipment must be appropriate to the work, the work site and the hazards |
Part 39 covers tree care operations. It applies to arboriculture that involves pruning, repairing, maintaining or removing trees or cutting brush while a worker works at height and depends on the tree for support. Section 795 names the standards for a harness made on or after March 31, 2023 and used in a work positioning system.
- NFPA 1983, 2006 edition, as a Class II or Class III life safety harness
- CEN EN 813:1997, sit harnesses
- CSA Z259.10-18, full body harnesses
- ANSI/ASSE Z359.1-2007, personal fall arrest systems, subsystems and components
- CEN EN 361:2007, full body harnesses
Section 795 does not apply to harnesses in use before April 30, 2004. Section 794 requires a work positioning system where fall protection under section 139 is not reasonably practicable.
Ireland, Health and Safety Authority chain saw documents
The HSA guidance on safe use of chainsaws and its chain saw safety advice sheet list the same equipment, with the same standards. Both say PPE cannot give complete protection against cuts, and that no PPE protects against falling trees.
| Item | Standard |
|---|---|
| Safety helmet | EN 397 |
| Eye protection | Visor to EN 1731, or safety glasses to EN 166 |
| Ear defenders | EN 352 |
| Chainsaw gloves | Protective pad on the back of the left hand; no standard printed for the gloves |
| Leg protection incorporating clogging material | EN 381-7 |
| Chainsaw trousers | EN 381-5 |
| Safety boots with steel toecaps and good grip | EN 381/345 |
The advice sheet adds that operators need a written risk assessment before the work and a chain saw training course with an assessment suited to the work planned. It says a basic course covering the felling of small trees runs up to five days.
Great Britain, HSE on PPE for aerial tree work
The HSE page lists what chain saw users wear when climbing trees. It quotes AFAG recommendations and points to AFAG 308 on top-handled chainsaws.
| Item | Standard |
|---|---|
| Safety helmet | AFAG recommends a mountaineering style helmet complying with BS EN 12492 |
| Eye protection | BS EN 1731 or BS EN 166 |
| Hearing protection | BS EN 352 |
| Leg and groin protection | BS EN 381-5. AFAG strongly recommends Type C for aerial work. Type A may be appropriate where a risk assessment justifies it, for example where heat stress makes Type C impractical |
| Protective boots | BS EN ISO 20345, with good grip and guarding at the front vamp and instep |
| Gloves | Suitable gloves for the task, subject to the operator's risk assessment; no standard printed |
Chain saw PPE rules by country are covered in the guide to chain saw operator PPE rules.
Sources
- Government of Alberta, Occupational Health and Safety Code (Alberta Regulation 191/2021), Part 18 Personal Protective Equipment, read October 21, 2026
- Government of Alberta, Occupational Health and Safety Code (Alberta Regulation 191/2021), Part 39 Tree Care Operations, read October 21, 2026
- Health and Safety Authority (Ireland), Guidance on Safe Use of Chainsaws, read October 21, 2026
- Health and Safety Authority (Ireland), Chainsaw safety advice information sheet, read October 21, 2026
- Health and Safety Executive (Great Britain), Personal Protective Equipment (PPE) for aerial tree work, read October 21, 2026