ArbNation Join free

Equipment standards named by regulators: Alberta, Ireland and Great Britain tree-work rules

Alberta's OHS Code names CSA, ANSI, ASTM, CEN and NFPA standards for eyewear, footwear, headwear and work positioning harnesses. Ireland's HSA and Britain's HSE name EN standards for chain saw and aerial PPE.

Checked against the sources at the bottom of this page on October 21, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. It extends the PPE standards matrix. Three regulators are added. Alberta's Occupational Health and Safety Code (Alberta Regulation 191/2021, Parts 18 and 39) comes first. Next are two Health and Safety Authority (HSA) chain saw documents for Ireland. The Health and Safety Executive (HSE) page on PPE for aerial tree work in Great Britain comes last.

Alberta, Occupational Health and Safety Code

Part 18 covers personal protective equipment. Section 228 puts a duty on the employer to see that workers wear PPE correct for the hazard when the hazard assessment shows the need, and on the worker to wear and inspect it. The sections that name standards are 229 for eyes, 233 for feet and 234 for heads.

Standards named in Part 18
ItemStandard the Code names
Eye and face protectors (s. 229)CSA Z94.3-15. Prescription frames may meet ANSI Z87.1-2003, and treated safety glass lenses may meet ANSI Z87.1-2003 or Z87.1-1989 where plastic lenses are impracticable and there is no impact danger
Protective footwear (s. 233), where the hazard assessment calls for toe protection, a puncture resistant sole, metatarsal, electrical or chainsaw protectionCSA Z195-14, or ASTM F2413-05 for footwear made on or after March 31, 2023
Protective headwear (s. 234), where lateral impact to the head is a significant possibilityCAN/CSA Z94.1-15, or ANSI Z89.1-2003 Type II, for headwear made on or after March 31, 2023
Protective headwear (s. 234), where lateral impact is unlikelyCAN/CSA Z94.1-05, or ANSI Z89.1-2003, for headwear made on or after July 1, 2009
Flame resistant outerwear (s. 232), where a worker may meet a flash fire or electrical equipment flashoverNo standard named
Limb and body protection (s. 242)No standard named; the equipment must be appropriate to the work, the work site and the hazards

Part 39 covers tree care operations. It applies to arboriculture that involves pruning, repairing, maintaining or removing trees or cutting brush while a worker works at height and depends on the tree for support. Section 795 names the standards for a harness made on or after March 31, 2023 and used in a work positioning system.

  • NFPA 1983, 2006 edition, as a Class II or Class III life safety harness
  • CEN EN 813:1997, sit harnesses
  • CSA Z259.10-18, full body harnesses
  • ANSI/ASSE Z359.1-2007, personal fall arrest systems, subsystems and components
  • CEN EN 361:2007, full body harnesses

Section 795 does not apply to harnesses in use before April 30, 2004. Section 794 requires a work positioning system where fall protection under section 139 is not reasonably practicable.

Ireland, Health and Safety Authority chain saw documents

The HSA guidance on safe use of chainsaws and its chain saw safety advice sheet list the same equipment, with the same standards. Both say PPE cannot give complete protection against cuts, and that no PPE protects against falling trees.

Standards named in the HSA documents
ItemStandard
Safety helmetEN 397
Eye protectionVisor to EN 1731, or safety glasses to EN 166
Ear defendersEN 352
Chainsaw glovesProtective pad on the back of the left hand; no standard printed for the gloves
Leg protection incorporating clogging materialEN 381-7
Chainsaw trousersEN 381-5
Safety boots with steel toecaps and good gripEN 381/345

The advice sheet adds that operators need a written risk assessment before the work and a chain saw training course with an assessment suited to the work planned. It says a basic course covering the felling of small trees runs up to five days.

Great Britain, HSE on PPE for aerial tree work

The HSE page lists what chain saw users wear when climbing trees. It quotes AFAG recommendations and points to AFAG 308 on top-handled chainsaws.

Standards named on the HSE aerial PPE page
ItemStandard
Safety helmetAFAG recommends a mountaineering style helmet complying with BS EN 12492
Eye protectionBS EN 1731 or BS EN 166
Hearing protectionBS EN 352
Leg and groin protectionBS EN 381-5. AFAG strongly recommends Type C for aerial work. Type A may be appropriate where a risk assessment justifies it, for example where heat stress makes Type C impractical
Protective bootsBS EN ISO 20345, with good grip and guarding at the front vamp and instep
GlovesSuitable gloves for the task, subject to the operator's risk assessment; no standard printed

Chain saw PPE rules by country are covered in the guide to chain saw operator PPE rules.

Sources