Escape routes and retreat paths in felling: what regulators and training guides require
OSHA calls it a retreat path, WorkSafeBC and the New Zealand and New South Wales codes call it an escape route. They agree on planning and clearing it before the cut, and differ on angle and length: 45 degrees, 3 metres, 6 metres.
Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The wording below is what the named codes and training bodies publish. It is not training and does not teach the work.
The wording by source
| Source | Escape route or retreat path |
|---|---|
| OSHA 29 CFR 1910.266, logging | Before felling starts, the feller plans and clears a retreat path. It extends diagonally away from the expected felling line, unless the employer demonstrates that it poses a greater hazard than an alternate path. Once the backcut is made, the feller moves a safe distance away on the path at once. Before felling, the chain-saw operator clears brush or obstacles that could interfere with cutting or with using the retreat path. The saw is shut off or the throttle released before the feller starts the retreat. |
| WorkSafeBC, OHS Regulation Part 26 | Before falling or bucking starts, obstructions are cleared and a safe escape route to a predetermined safe position is prepared. When a tree starts to fall, the faller and anyone else present move quickly to that position, at least 3 m (10 ft) from the base of the tree where possible, and take cover if available. Written safe work practices cover planning and constructing escape routes. Fall protection must not impede the faller's move to the position, and a faller does not work supported solely by a lifeline and harness. |
| SafeWork NSW, Tree works code of practice | The common controls for felling include a minimum 45-degree escape route extending at least 6 metres from the stump. Where that cannot be set up, alternative escape routes or other suitable controls are put in place. The operator should move away along the planned route as the tree begins to fall. Limbing and chainsaw sections add a clear escape route, a path of retreat that allows quick, unobstructed movement to a safe zone. |
| WorkSafe New Zealand, arboriculture code of practice | An escape route is planned and kept clear of tools and other material that would impede a quick exit. The ideal route is 45 degrees on either side of a line drawn opposite the intended direction of fall. A hung-up or cut-up tree is not left standing, and the feller does not leave the area before it is on the ground, other than to seek help. |
| Irish Forestry Safety Guide 302 (Health and Safety Authority) | The feller decides the direction of fall and selects an escape route, shown in the leaflet's Figure 1, and keeps it clear of obstructions. When the tree begins to fall and site conditions permit, the feller moves at least 3 metres into the escape route to be a safe distance from the butt, watching for falling branches and tops. The leaflet warns of the butt rebounding, and of the whole tree sliding when felling on a slope. |
| OSHA Hurricane eMatrix, chain saw and felling sheet | Lists planning where the object will fall, a clear fall area, and a clear retreat path, and shutting off or releasing the throttle before retreating. The sheet adds that it does not alter or determine compliance responsibilities in OSHA standards. |
Angle and length
The documents agree on the order of work: the route is chosen with the direction of fall, and it is cleared before the cut. They give different geometry.
OSHA states the angle loosely, diagonally away from the felling line, and gives no length: the feller moves "a safe distance". New Zealand and New South Wales both print 45 degrees. New South Wales adds the 6 metre length, measured from the stump, and its figure notes that all standing vegetation should be removed to provide a clear gap.
WorkSafeBC and the Irish leaflet print 3 metres, but as a destination, not a route length: the safe position or the point reached along the route once the tree starts to fall. WorkSafeBC adds that the distance is "where possible", and Ireland that site conditions must permit it.
The figures answer different questions. A 6 metre route in New South Wales is a length to clear. A 3 metre position in British Columbia and Ireland is a distance from the butt once the tree starts to fall.
Sloping ground and hung trees
Slopes change the picture in two of the documents. The Irish leaflet warns of the butt rebounding or the whole tree sliding. The New South Wales code says that on steep ground no person is positioned below the felling area.
The New Zealand code covers the case where the tree does not fall. A hung-up tree is brought to the ground as soon as possible and before operations continue. The feller does not leave until it is down, other than to get assistance, and the person in charge is notified.
Mobile plant
For mobile plant used in directional felling, the SafeWork NSW code has the tree feller and plant operator maintain clear communication and agree on a safe escape zone. The plant operator must remain in the cab until the tree is safely committed to fall. All ground workers must remain outside the drop zone once cutting begins.
Sources
- OSHA, 29 CFR 1910.266 Logging operations, read October 15, 2026
- WorkSafeBC, OHS Regulation Part 26, Forestry Operations, sections 26.23, 26.24 and 26.27, read October 15, 2026
- SafeWork NSW, Tree works code of practice, commenced March 27, 2026, read October 15, 2026
- WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture, November 2012, read October 15, 2026
- Health and Safety Authority (Ireland), Irish Forestry Safety Guide 302, Basic Chainsaw Felling and Manual Takedown, October 2018, hosted by Teagasc, read October 15, 2026
- OSHA, Hurricane eMatrix activity sheet: Tree Trimming, read October 15, 2026