Felling distances and danger zones: two tree-lengths and other minimum distances by regulator
OSHA, WorkSafeBC, WorkSafe New Zealand, SafeWork NSW and Ireland's forestry safety guide all print a distance of two tree-lengths around felling. They differ on who the distance protects, when it can shrink and what applies below it.
Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The wording below is what the named codes and regulators publish. It is not training and does not teach the work.
Distances by regulator
| Regulator and document | Distance and wording |
|---|---|
| OSHA, 29 CFR 1910.266, logging operations | Adjacent occupied work areas are at least two tree lengths of the trees being felled, and more than two tree lengths on a slope where rolling or sliding of trees or logs is foreseeable. No employee approaches a feller closer than two tree lengths until the feller has acknowledged that it is safe, unless the employer demonstrates that a team is needed to fell a particular tree. The same two tree lengths apply to a mechanical felling operation and its machine operator. |
| OSHA 1910.266, special cases | No yarding machine operates within two tree lengths of trees being manually felled, except for tree pulling. A danger tree that is not felled or removed is marked, and no work is done within two tree lengths of it unless the employer demonstrates that a shorter distance creates no hazard. When a spring pole is cut, no one but the feller is closer than two tree lengths. |
| WorkSafeBC, OHS Regulation Part 26 | Before a tree is felled, all workers are clear of the area within a 2 tree-length radius, with an exception in section 26.29(3) for a supervisor, a trainee faller or a worker needed to help with a falling difficulty. Before a mechanical harvester fells a tree, all workers and equipment except the operator and the harvester are clear of the same 2 tree-length radius. |
| SafeWork NSW, Tree works code of practice | Clear felling is usually used where there is a minimum of two tree lengths of open space in all directions from the base of the tree. Controlled directional felling is used where space is limited (less than two tree lengths) or the natural fall would meet overhead lines, structures or hung trees. On steep ground the code has no person positioned below the felling area. |
| WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture | People not directly helping with a felling stay at least two tree-lengths from the tree. No machine works within two tree-lengths of a felling unless helping, under supervision, to bring the tree down. If two tree-lengths of clearance is possible, a tree may be pulled towards the machine or its anchor. |
| Irish Forestry Safety Guide 302, Basic Chainsaw Felling and Manual Takedown (Health and Safety Authority, October 2018) | The leaflet covers felling with a minimum of two tree lengths of clear space in all directions. A safe working distance of two tree lengths is maintained, unless exceptional conditions and a full risk assessment dictate otherwise. For a lodged tree, no other person is within twice the length of the tree, or directly below it on steep slopes. |
| OSHA, Hurricane eMatrix tree trimming sheet | During felling, adjacent occupied work areas are at least two tree lengths from the tree being felled, with more allowed if the tree might roll or slide. |
| HSE, Great Britain, tree work case studies page | Defines the danger zone as an area to the front and rear of a tree, where the tree is most likely to fall during or after the sink and felling cuts. The page prints no distance. |
The distance and the zone are different things
OSHA's standard applies to logging, and its scope paragraph covers all types of logging whatever the end use of the wood. The eMatrix sheet carries the same two tree lengths into hurricane tree work. OSHA states that the matrix does not alter or determine compliance responsibilities in OSHA standards.
WorkSafeBC turns the distance into a defined term. The active falling area is the area within a 2 tree-length radius of where a faller or mechanized falling equipment is located and equipped to fall timber. Only a worker with duties tied to the falling may enter it, after notifying the faller or bucker and waiting for word that it is safe.
The HSE page uses the older word danger zone for the fall line itself. The Irish leaflet's diagrams label a danger zone and a working zone around the felled tree.
Where the figure changes
New South Wales ties the technique to the available space, so the two tree lengths decide between clear felling and controlled directional felling. The controlled method uses ropes, cables or mobile plant to guide the tree, and vehicles or plant used as anchors are kept outside the drop zone. Ireland scopes the whole leaflet to sites with that space and sends exceptional situations to specialist advice.
OSHA and the Irish leaflet both allow a different distance, but on different terms. OSHA lets the employer demonstrate a shorter distance for a danger tree, and a team exception for a particular tree. The Irish leaflet allows variation only where exceptional conditions and a full risk assessment call for it. WorkSafeBC names its own exceptions by role: a supervisor, a trainee faller, or a worker needed to overcome a falling difficulty.
The New Zealand code is dated November 2012 and the New South Wales code commenced on March 27, 2026. The Irish leaflet was modified for Irish use from material by the Forest Industry Safety Accord, with permission.
Sources
- OSHA, 29 CFR 1910.266 Logging operations, read October 15, 2026
- WorkSafeBC, OHS Regulation Part 26, Forestry Operations, read October 15, 2026
- SafeWork NSW, Tree works code of practice, commenced March 27, 2026, read October 15, 2026
- WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture, November 2012, read October 15, 2026
- Health and Safety Authority (Ireland), Irish Forestry Safety Guide 302, Basic Chainsaw Felling and Manual Takedown, October 2018, hosted by Teagasc, read October 15, 2026
- OSHA, Hurricane eMatrix activity sheet: Tree Trimming, read October 15, 2026
- HSE, Tree work: case studies and terms, read October 15, 2026