ArbNation Join free

Felling that goes wrong: barber chair, lodged trees and spring poles in regulator records

WorkSafeBC and a Michigan state report both describe a tree that split up the trunk and kicked back onto the feller. OSHA's logging standard defines the lodged tree, the danger tree and the spring pole.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

The named codes and training bodies are described here as published. It is not training and does not teach the work. The terms and events below come from WorkSafeBC, OSHA and a Michigan state fatality report. No victim is named.

Terms as OSHA prints them

OSHA's logging standard, 29 CFR 1910.266, has a definitions list. Four entries cover events that tree crews also meet.

TermOSHA definition, restated
Lodged tree (hung tree)A tree leaning against another tree or object that stops it falling to the ground
Danger treeA standing tree that presents a hazard due to conditions such as, but not limited to, deterioration or physical damage to the root system, trunk, stem or limbs, and the direction and lean of the tree
Spring poleA tree, segment, limb or sapling held under stress or tension by the pressure or weight of another object
UndercutA notch cut in a tree to guide the direction of the fall and to prevent splitting or kickback

The standard also defines domino felling as the partial cutting of several standing trees that are then pushed over with a pusher tree. Paragraph (h)(1)(ix) prohibits it.

OSHA felling paragraphs

  • Danger trees. Each one is felled, removed or avoided, lodged trees and snags included. If it stays, it is marked, and no work happens within two tree lengths unless the employer shows a shorter distance creates no hazard. Paragraph (h)(1)(vi).
  • Checking before felling. A danger tree is checked for loose bark, broken branches and limbs, and other damage. Paragraph (h)(1)(vii).
  • Spring poles. When one is cut, no one but the feller is closer than two tree lengths as the stress is released. Paragraph (h)(2)(iv).
  • Undercut and backcut. Each tree gets an undercut sized so it will not split and will fall in the intended direction, unless the employer shows it is not needed. The backcut sits above the horizontal facecut to give a platform that prevents kickback, with an exception for tree pulling operations. Paragraphs (h)(2)(v) and (h)(2)(vii).
  • Wind-thrown trees. Before bucking or limbing, precautions keep the root wad, butt or logs from striking an employee. Chocking or moving the tree to a stable position is one. Paragraph (h)(3)(ii).

The standard covers logging operations, as laid out in the guide to OSHA 1910.266.

A barber chair in a WorkSafeBC summary

In April 2022 two workers were clearing brush beside a forest service road. One was felling a leaning alder, about 27.9 cm (11 in.) across at the stump. The trunk barberchaired, which the report glosses as split vertically. As the tree fell, the trunk kicked back and struck him. He later died.

WorkSafeBC lists the cause as an unqualified worker struck by a tree while felling it. Its conclusions on contributing factors:

  • The worker was experienced with a chainsaw as a bucker but was not a qualified tree faller. WorkSafeBC says a qualified faller should have been sought once the work moved to manual falling of trees over 15 cm (6 in.).
  • No escape route had been planned, and he had not moved far enough from the falling tree.
  • The undercut was incorrect and incomplete for a leaning deciduous tree. The backcut was not placed where it would have lowered the risk of a barber chair.
  • WorkSafeBC says the employer ought to have made certain the supervisor knew that trees of 15 cm (6 in.) or more are required to be felled by a qualified tree faller.

The report names the employer only as a logging services company.

A second barber chair in a Michigan report

Michigan's fatality assessment program, MIFACE, records Case 375. A 48-year-old landscape worker stood in the crotch of a 50-foot willow, about 7 feet up, removing a trunk section about 30 inches across. The section leaned very slightly away from him. He had not notched it before the backcut. The tree splintered, barber-chaired and kicked back onto his chest.

The Michigan occupational safety agency issued two serious citations. One was for no training under Part 53, Tree Trimming and Removal. The other was for no head protection. The case notes record no clear path of retreat, no undercut or notch, and signs of plunge cutting in photos.

Related regulator wording

Felling cuts from OSHA, HSE, NSW and New Zealand are compared in felling cuts and hazards. Planned exits are covered in escape routes and retreat paths.

To correct or remove an entry, write to the address at the foot of this page.

Sources