ArbNation Join free

The felling plan: TCI's six steps and the planning wording in OSHA, NSW and NZ codes

TCI Magazine's Six-Step Felling Plan runs from site risk to the back cut. OSHA, SafeWork NSW and WorkSafe New Zealand word the planning that comes before a fell, and the UK code lists what must be in place for work at height.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

The wording below is what the named codes and training bodies publish. It is not training and does not teach the work.

The six steps in TCI Magazine

The Six-Step Felling Plan was written by Rebecca Seibel, a Board Certified Master Arborist and Certified Treecare Safety Professional, for TCI Magazine on October 1, 2024. It is based on her TCI EXPO 2022 talk. She calls it a checklist for every felling operation, a training tool and an assessment template for in-house trainers. Verbalizing each step, she writes, makes the operation safer and teaches by modeling.

The six steps and what the article puts under each
StepWhat the article lists
1. Overall site-risk assessmentAn outer perimeter look at electrical hazards, which are assumed present until positively ruled out, then traffic, incoming severe weather, terrain and neighbouring trees. An inner look at the tree itself, walking the full 360 degrees for cavities, decay, cracks, damaged trunk flare and fungal fruiting bodies. Objects and hazards on site are identified and written into the job-site safety analysis. The tree to be felled is confirmed by a mark.
2. Tree assessmentTree height, lean, load and slope. Height decides the size of the drop zone and the work zones. Lean is judged from several directions. The article notes a forward leaner is more likely to split vertically, which it calls barber chair.
3. EquipmentThe equipment that fits the plan, and the experience and skills of each crew member. The article calls this a turning point: if the right tools or people are not present, it is wise to pause.
4. Retreat routeA preplanned route at an angle away from the intended fall, cleared of limbs, vines and small stumps. The article cites the 90-15-5 rule: 90% of incidents happen within 15 seconds of a tree starting to move, and within 5 feet of the trunk. It names a second turning point.
5. Notch planThe directional face notch, which gives the tree direction and forms the hinge. Three types are named: the traditional 45-degree notch, the open-face notch and the Humboldt notch.
6. Back cut or bore cut and release planCalling out the cut, agreeing tension on any line with the ground team, and a bore cut with a trigger release where the tree has a slight forward lean or the faller needs more time to retreat.

The article ends by saying the whole crew signs off on the plan, as with a job-site safety analysis, and that anyone on the crew can question it or raise a risk.

Planning in the OSHA logging standard

OSHA's logging standard, 29 CFR 1910.266, applies to logging operations. Its manual felling paragraph, (h)(2), requires the feller to plan and clear a retreat path before felling starts. The path runs diagonally away from the expected felling line, unless the employer shows it poses a greater hazard than an alternate path.

Before each tree is felled, the feller evaluates snow and ice accumulation, wind, the lean of the tree, dead limbs and the location of other trees. The standard also requires an undercut, unless the employer shows it is not needed, and a backcut with enough hinge wood to guide the fall. Work areas are assigned so a tree cannot fall into an adjacent occupied area, at least two tree lengths apart, and more on slopes where trees or logs may roll or slide. Paragraph (d)(5) stops all work in conditions such as electrical storms and strong winds that may affect the fall of a tree.

Planning in the New Zealand and New South Wales codes

WorkSafe New Zealand's arboriculture code puts planning ahead of any removal. The operator or crew leader considers the surrounding area including other trees, the species, shape and condition of the tree, and its lean. The code says only a competent person fully experienced in the work does the felling, and the person in charge supervises. Its ideal escape route is 45 degrees on either side of a line opposite the intended fall. People not helping stay at least two tree lengths away. Dead trees get special care.

The SafeWork NSW Tree works code of practice, section 9, sorts felling into clear, controlled directional and sectional felling. Clear felling is usually used where there is a minimum of two tree lengths of open space in all directions from the base of the tree. Controlled directional felling is for less space, or where a natural fall would meet overhead lines, structures or hung trees. Its common controls start with assessing the tree for hazards and keeping separation from people and property. They add exclusion and drop zones, and no one below the felling area on steep ground. Another is a minimum 45-degree escape route extending at least 6 metres from the stump.

The UK code on planning

The Industry Code of Practice for tree work at height lists six things in place before aerial work starts. They are a check that working at height is appropriate, safe systems of work, trained operators, a point-of-work risk assessment, emergency planning including aerial rescue, and a plan communicated to the team. The code says its principles may also be used for other tree work operations such as ground-based chainsaw work. It does not give a numbered felling plan.

Sources