Firewood heat values by species: Kansas State, Penn State and Utah State tables
Three extension tables give heat per cord by species, and they differ: Osage orange runs from 30.7 to 32.9 million BTU, and white oak from 25.7 to 29.1.
Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.
Three extension tables give heat value per cord by species, and they do not agree. One University of Maryland sheet adds a fourth basis for comparison. Figures are in million British thermal units (BTU) per cord.
Kansas State: Johnson County Extension
K-State Extension in Johnson County, Kansas, lists heat values in million BTU per cord in an agent article titled Not All Firewood Is Equal. The article states no moisture content and no cord volume. It says the higher the value, the better the wood, and adds that some of the species are difficult to split.
| Species | Million BTU per cord | Note in the article |
|---|---|---|
| Ash, Green | 22.8 | |
| Cottonwood | 15.9 | |
| Elm, American | 19.8 | Difficult to split |
| Elm, Red | 20.6 | Difficult to split |
| Elm, Siberian | 20.9 | Difficult to split |
| Hackberry | 21.0 | |
| Honeylocust | 25.6 | |
| Locust, Black | 28.3 | Difficult to split |
| Maple, Sugar | 24.0 | |
| Maple, Silver | 18.9 | |
| Mulberry | 25.3 | |
| Oak, Red | 24.0 | |
| Oak, Bur | 24.9 | |
| Oak, Post | 25.6 | |
| Osage Orange (Hedge) | 32.6 | Sparks |
| Sycamore | 19.5 | Difficult to split |
| Walnut, Black | 21.8 |
Penn State Extension
Penn State Extension, in Heating with Wood: An Introduction, prints its table as the energy value of an air-dried cord of common hardwoods of the northeastern United States, with an assumed moisture content of 20 percent. The table credits Hank Stelzer, 2017. Penn State notes that a ton of anthracite coal produces 25 million BTU, which would place coal seventh on the table, and that heating values may differ in other reports because of methodology and the individual trees tested.
| Species | Million BTU per cord at an assumed 20 percent moisture |
|---|---|
| Osage orange | 30.7 |
| Ironwood or hop hornbeam | 27.3 |
| Hickory (shagbark, bitternut, mockernut, pignut) | 28.0 |
| Hornbeam or blue beech | 26.8 |
| Black birch | 26.8 |
| Honey locust | 26.7 |
| White oak group | 25.7 |
| Sugar maple | 24 |
| Red oak group | 24 |
| White ash | 23.6 |
| Yellow birch | 23.6 |
| Hackberry | 20.8 |
| Birch (paper, gray, river) | 20.3 |
| Black walnut | 20.2 |
| Black cherry | 19.9 |
| Maple (red and silver) | 18.7 |
Utah State University Extension
Utah State University Extension publishes Wood Heating by Michael Kuhns and Tom Schmidt, with a firewood facts table covering most species used in Utah. It gives the heat per cord of dry wood, where dry weight is the weight of a cord after air drying. No moisture percentage is printed for that basis. It also says green firewood may contain 50 percent or more water by weight, and defines a cord as an evenly stacked pile of 128 cubic feet of wood and air space. A blank cell in the Utah table means no figure was printed, and species with no heat value are left out here.
| Species | Million BTU per cord of dry wood |
|---|---|
| Alder | 17.5 |
| Apple | 27.0 |
| Ash, green | 20.0 |
| Ash, White | 24.2 |
| Aspen, Quaking | 18.2 |
| Basswood (Linden) | 13.8 |
| Beech | 27.5 |
| Birch | 20.8 |
| Boxelder | 18.3 |
| Buckeye, Horsechestnut | 13.8 |
| Catalpa | 16.4 |
| Cherry | 20.4 |
| Chestnut | 18.0 |
| Coffeetree, Kentucky | 21.6 |
| Cottonwood | 15.8 |
| Douglas-fir | 20.7 |
| Elm, American | 20.0 |
| Elm, Siberian | 20.9 |
| Fir, White | 14.6 |
| Hackberry | 21.2 |
| Hemlock | 19.3 |
| Honeylocust | 26.7 |
| Juniper, Rocky Mountain | 21.8 |
| Larch (Tamarack) | 21.8 |
| Locust, Black | 27.9 |
| Maple, Other | 25.5 |
| Maple, Silver | 19.0 |
| Mulberry | 25.8 |
| Oak, Bur | 26.2 |
| Oak, Gambel | 30.7 |
| Oak, Red | 24.6 |
| Oak, White | 29.1 |
| Osage-orange | 32.9 |
| Pine, Lodgepole | 21.1 |
| Pine, Ponderosa | 16.2 |
| Pine, White | 15.9 |
| Pinyon | 27.1 |
| Redcedar, Eastern | 13.0 |
| Redcedar, Western | 18.2 |
| Spruce | 15.5 |
| Spruce, Engelmann | 15.0 |
| Sycamore | 19.5 |
| Walnut, Black | 22.2 |
| Willow | 17.6 |
Species in more than one table
| Species | Kansas | Penn State | Utah |
|---|---|---|---|
| Red oak | 24.0 | 24 (group) | 24.6 |
| White oak | 25.7 (group) | 29.1 | |
| Sugar maple | 24.0 | 24 | |
| Silver maple | 18.9 | 18.7 (red and silver) | 19.0 |
| Black walnut | 21.8 | 20.2 | 22.2 |
| Hackberry | 21.0 | 20.8 | 21.2 |
| Honeylocust | 25.6 | 26.7 | 26.7 |
| Osage orange | 32.6 | 30.7 | 32.9 |
| Green ash | 22.8 | 20.0 | |
| White ash | 23.6 | 24.2 |
The Kansas and Utah tables both list Siberian elm at 20.9 and sycamore at 19.5. Penn State prints black birch at 26.8 and yellow birch at 23.6, and Utah prints one birch figure of 20.8.
The Maryland sheet for comparison
University of Maryland Extension fact sheet FS-937 (2012) prints heat in million BTU per cord for six species: oak 25.3, ash 23.6, walnut 21.8, elm 21.4, sycamore 20.7 and white pine 19.0. It does not state a moisture content next to those figures. It defines a standard cord as 128 cubic feet, with the actual volume of wood between 65 and 90 cubic feet depending on size, straightness and moisture content of the logs, and about 80 cubic feet on average in Maryland.
Ash alone shows how the bases differ. The Kansas figure for green ash is 22.8 and the Utah figure is 20.0. White ash is 23.6 at Penn State and 24.2 at Utah State. Maryland prints 23.6 for ash without naming the species.
Sources
- K-State Research and Extension, Johnson County, Not All Firewood Is Equal (page updated June 30, 2026), read October 15, 2026
- Penn State Extension, Heating with Wood: An Introduction, read October 15, 2026
- Michael Kuhns and Tom Schmidt, Utah State University Extension, Wood Heating, read October 15, 2026
- University of Maryland Extension, Buying and Storing Firewood and Pellets (FS-937), 2012, read October 15, 2026