Lumber kilns by type: conventional, dehumidification, solar and vacuum
The USDA Forest Service's Wood Handbook names five kiln types: track-loaded, package-loaded, dehumidification, vacuum and progressive. Oklahoma State and Virginia Tech Extension add how conventional, dehumidification and solar kilns work.
Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.
The USDA Forest Products Laboratory's Wood Handbook chapter on drying (General Technical Report FPL-GTR-282), an Oklahoma State University fact sheet and a Virginia Tech publication all cover lumber kilns. None describes a kiln built for firewood.
Kiln types
The Wood Handbook says most dry kilns are insulated compartments that work as a batch process. The kiln is loaded in one operation and the lumber stays still for the whole cycle. Temperature and relative humidity change on a schedule tied to the moisture content or drying rate of the lumber. All kilns use forced air that moves across the stack, parallel to the stickers.
| Type | What the sources describe |
|---|---|
| Track-loaded | Wood Handbook: lumber stacked on kiln trucks that roll in and out on tracks. Most softwood lumber in the United States is dried this way |
| Package-loaded | Wood Handbook: stacks of lumber placed by forklift. Commonly used for hardwood lumber |
| Conventional | Oklahoma State: steam flows through pipes and radiates heat into the kiln. Moisture leaves as vapor in the hot air that is vented. The Wood Handbook says the heat usually comes from steam boilers fueled mainly by mill residues such as hog fuel, plus some fossil fuel |
| Dehumidification | Wood Handbook: usually package loaded, with water condensing on cold dehumidifier coils instead of being vented. Oklahoma State gives an air temperature of 95 to 100 degrees F |
| Vacuum | Wood Handbook: drying happens below atmospheric pressure, so lumber dries at lower temperatures. Oklahoma State calls the main advantage a very high drying speed |
| Progressive (continuous flow) | Wood Handbook: cross-sectional air circulation and multizone control, which reduce energy use and raise productivity over conventional batch kilns |
| Solar | Virginia Tech: sunlight heats the air inside a glazed collector space and fans move it through the lumber. Humid air leaves through vents |
The Wood Handbook says vacuum and progressive kilns are more common in the Scandinavian countries but are becoming more prevalent in the United States. Oklahoma State calls conventional and dehumidification kilns the most commonly used, and vacuum and solar kilns special-application types.
Moisture content of dried lumber
The Wood Handbook defines kiln dry lumber as lumber dried in a kiln, or by some special drying method, to an average moisture content suited to a use. It gives three figures.
| Product | Moisture content the Wood Handbook prints |
|---|---|
| Kiln-dried softwood dimension lumber | Average of 19 percent or less |
| Many other softwood uses | 10 to 20 percent |
| Hardwood and softwood lumber for furniture, cabinetry and millwork | Usually 6 to 8 percent final |
| Air-dried lumber, for comparison | For much of the United States, the minimum for thoroughly air-dried lumber is 12 to 15 percent |
| Shipping dry | Ideally the outer 3.2 mm (1/8 inch) at 25 percent or less |
Virginia Tech makes the same point from the other side. Humidity in most localities keeps air-dried lumber from reaching the moisture content that interior use needs, and a dry kiln reaches the final moisture content fairly rapidly. Its solar kiln dries a load in approximately one month of moderately sunny weather at Blacksburg, Virginia.
Oklahoma State prints a sample hardwood schedule that starts at 110 to 120 degrees F and 70 to 80 percent relative humidity when lumber is green. The temperature could reach 170 to 180 degrees F by the time the lumber is at 10 to 15 percent moisture content. Schedules vary by species, thickness, grade and intended final use. The Wood Handbook adds that softwood schedules differ from hardwood schedules, and that Southern Pine structural lumber is usually dried at a constant temperature and humidity.
Firewood and the kiln publications
The sources print no target moisture content for firewood. The Wood Handbook figures above are for lumber. Virginia Tech gives lumber targets by use: 6 to 8 percent for interior use, 12 to 15 percent for exterior use and usually 19 percent for softwood framing.
Sources
- USDA Forest Service, Forest Products Laboratory, Wood Handbook, General Technical Report FPL-GTR-282, Chapter 13, Drying and Control of Moisture Content and Dimensional Changes, read October 15, 2026
- Brian Bond, Virginia Cooperative Extension, Design and Operation of a Solar-Heated Dry Kiln, publication 420-030, read October 15, 2026
- Salim Hiziroglu, Oklahoma State University, Fundamental Aspects of Kiln Drying Lumber, fact sheet FAPC-146, read October 15, 2026