ArbNation Join free

Lumber kilns by type: conventional, dehumidification, solar and vacuum

The USDA Forest Service's Wood Handbook names five kiln types: track-loaded, package-loaded, dehumidification, vacuum and progressive. Oklahoma State and Virginia Tech Extension add how conventional, dehumidification and solar kilns work.

Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.

The USDA Forest Products Laboratory's Wood Handbook chapter on drying (General Technical Report FPL-GTR-282), an Oklahoma State University fact sheet and a Virginia Tech publication all cover lumber kilns. None describes a kiln built for firewood.

Kiln types

The Wood Handbook says most dry kilns are insulated compartments that work as a batch process. The kiln is loaded in one operation and the lumber stays still for the whole cycle. Temperature and relative humidity change on a schedule tied to the moisture content or drying rate of the lumber. All kilns use forced air that moves across the stack, parallel to the stickers.

Kiln types
TypeWhat the sources describe
Track-loadedWood Handbook: lumber stacked on kiln trucks that roll in and out on tracks. Most softwood lumber in the United States is dried this way
Package-loadedWood Handbook: stacks of lumber placed by forklift. Commonly used for hardwood lumber
ConventionalOklahoma State: steam flows through pipes and radiates heat into the kiln. Moisture leaves as vapor in the hot air that is vented. The Wood Handbook says the heat usually comes from steam boilers fueled mainly by mill residues such as hog fuel, plus some fossil fuel
DehumidificationWood Handbook: usually package loaded, with water condensing on cold dehumidifier coils instead of being vented. Oklahoma State gives an air temperature of 95 to 100 degrees F
VacuumWood Handbook: drying happens below atmospheric pressure, so lumber dries at lower temperatures. Oklahoma State calls the main advantage a very high drying speed
Progressive (continuous flow)Wood Handbook: cross-sectional air circulation and multizone control, which reduce energy use and raise productivity over conventional batch kilns
SolarVirginia Tech: sunlight heats the air inside a glazed collector space and fans move it through the lumber. Humid air leaves through vents

The Wood Handbook says vacuum and progressive kilns are more common in the Scandinavian countries but are becoming more prevalent in the United States. Oklahoma State calls conventional and dehumidification kilns the most commonly used, and vacuum and solar kilns special-application types.

Moisture content of dried lumber

The Wood Handbook defines kiln dry lumber as lumber dried in a kiln, or by some special drying method, to an average moisture content suited to a use. It gives three figures.

ProductMoisture content the Wood Handbook prints
Kiln-dried softwood dimension lumberAverage of 19 percent or less
Many other softwood uses10 to 20 percent
Hardwood and softwood lumber for furniture, cabinetry and millworkUsually 6 to 8 percent final
Air-dried lumber, for comparisonFor much of the United States, the minimum for thoroughly air-dried lumber is 12 to 15 percent
Shipping dryIdeally the outer 3.2 mm (1/8 inch) at 25 percent or less

Virginia Tech makes the same point from the other side. Humidity in most localities keeps air-dried lumber from reaching the moisture content that interior use needs, and a dry kiln reaches the final moisture content fairly rapidly. Its solar kiln dries a load in approximately one month of moderately sunny weather at Blacksburg, Virginia.

Oklahoma State prints a sample hardwood schedule that starts at 110 to 120 degrees F and 70 to 80 percent relative humidity when lumber is green. The temperature could reach 170 to 180 degrees F by the time the lumber is at 10 to 15 percent moisture content. Schedules vary by species, thickness, grade and intended final use. The Wood Handbook adds that softwood schedules differ from hardwood schedules, and that Southern Pine structural lumber is usually dried at a constant temperature and humidity.

Firewood and the kiln publications

The sources print no target moisture content for firewood. The Wood Handbook figures above are for lumber. Virginia Tech gives lumber targets by use: 6 to 8 percent for interior use, 12 to 15 percent for exterior use and usually 19 percent for softwood framing.

Sources