FISA 310: winches in directional felling and takedown
FISA 310 is the Forest Industry Safety Accord leaflet on tractor and hand winches in directional felling and takedown. HSE and Forest Research publish matching guidance: agreed signals first, an unclear signal read as stop.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
The named codes and training bodies are described here as published. It is not training and does not teach the work. Some wording is adapted from HSE and Forest Research pages published under the Open Government Licence v3.0.
Scope of the leaflet
The Forest Industry Safety Accord lists FISA 310 as "Use of winches in directional felling and takedown". Its summary says the leaflet covers safe working practices when a tractor winch or a hand winch is used as an aid to directional felling and takedown in forestry and tree work. FISA numbers its guides in series, and the 300s are the chainsaw guides. The leaflet itself is a downloadable PDF on the FISA safety guides page.
The Health and Safety Executive (HSE) page on winches in directional felling uses nearly the same scope line. It adds a limit: the guidance does not cover machines or winches used for timber extraction, or for towing vehicles and other equipment.
Signals agreed before work starts
HSE puts communication first. A clear system is agreed before starting work, and three rules sit inside it.
- The chainsaw operator is in control and gives the instructions to the machine operator.
- An emergency stop signal is obeyed at once by everyone.
- Any unclear signal is read as a stop signal.
Where the chainsaw operator cannot see the machine operator, HSE calls for another method: a radio, or a third person who relays the message. The WorkSafe New Zealand code for arboriculture lands in the same place. Its section on winching has the tree feller tell winch and machinery operators the line tension and the winching and pulling speeds needed. Visual signals and vocal commands are set before felling starts.
Training for the machine operator
HSE lists four things every operator must be trained in:
- how to operate the machine
- how to do the tasks required
- the use of personal protective equipment
- how to keep the machine in good working order
The same four items appear on the HSE page on machine-assisted takedown. That page opens with the reason for it: many incidents have happened where machines were used to bring down large edge trees and hung-up or leaning trees.
The Forest Research technical guide
Forest Research, for the Forestry Commission, published a Technical Guide on winching operations in forestry, covering tree takedown and vehicle debogging. It is dated 2004. The guide sets out basic principles on winch forces and fail-safe systems, and discusses where safety shortfalls commonly occur. It gives guidance on controlled failure of winch systems. Its example set-ups illustrate the forces involved and the equipment rating for hypothetical takedown and debogging situations.
The guide covers static hand winches and vehicle-mounted mechanised winches. It leaves out vehicles used for pulling operators. It also leaves out winches used for lifting, which it calls a separate subject because of the lifting equipment legislation. Forest Research states that the guide is not a substitute for training: anyone involved in winching must first have received the appropriate technical and first-aid training.
HSE on pulling lines in felling
The HSE page on chainsaws gives three cases to avoid when control lines or pull ropes assist a fell.
- Free hand pulling or non-anchored pulling. If the person on the rope sways or rocks the tree, the felling cut can open and close and the chainsaw operator can compromise the hinge.
- Over-tensioned lines. These can load the rear of the tree, sever the hinge early, split the tree and injure the operator.
- Making the back cut while a workmate applies tension. The operator cannot place the cut safely and also watch the person on the line.
HSE adds that in the majority of cases the tree feller should be able to form the back cut and leave a hinge of the right size. After that come a step into a safe area and an agreed signal for the line to start.
Contains public sector information published by the Health and Safety Executive and Forest Research and licensed under the Open Government Licence v3.0.
Sources
- Forest Industry Safety Accord, FISA 310 Use of winches in directional felling and takedown, guide page, read October 16, 2026
- Health and Safety Executive, Winches in directional felling, read October 16, 2026
- Health and Safety Executive, Machine-assisted takedown, read October 16, 2026
- Health and Safety Executive, Working with chainsaws, read October 16, 2026
- Forest Research, Winching operations in forestry: tree takedown and vehicle debogging, Technical Guide 2004, read October 16, 2026
- WorkSafe New Zealand, approved code of practice for safety and health in arboriculture, section 3.4.6, read October 16, 2026