ArbNation Join free

Glossary: hand tools for tree work by type

Hand pruners, loppers, pruning saws, pole pruners, pole saws and chainsaws, defined from three university extension guides, OSHA's logging standard and one maker's folding saw page.

Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.

The named codes and training bodies are described here as published. It is not training and does not teach the work.

Cutting size by tool type

The three extension guides do not agree on how thick a branch each tool handles. Each figure below is the guide's own.

Branch diameters the extension guides give for each tool
ToolIowa StateNC StateMaryland
Hand prunerUp to 3/4 inchSmall limbs, usually under 1/2 inchUp to 1 inch
Lopper3/4 to 1-1/2 inches1/2 inch to about 1-1/2 inchesUp to 3 inches
Pruning sawLarger than 1-3/4 inchesLarger than 1-1/2 inchesNo figure
Pole saw or pole prunerUp to 2 inchesNo figureNo figure

Hand pruners

Bypass hand pruner

Iowa State describes bypass pruners as scissor-type, with curved blades that overlap during the cut. In Maryland's account a curved blade slides past a broader blade, and bypass pruners beat anvil pruners because they tear and crush less tissue. NC State calls bypass shears by far the most commonly used hand pruners.

Anvil hand pruner

An anvil pruner has one sharpened upper blade that cuts against a flat surface. Iowa State finds anvil pruners good on dead branches and less prone to jamming than bypass pruners, but unable to cut as close and more likely to crush stems. NC State adds that newer designs use a curved anvil and blade, which gives a much cleaner cut.

Loppers and shears

Lopper

A lopper is a pruner on long handles. The long handles give Iowa State's loppers pull on larger branches and reach into awkward spots. Loppers come in bypass and anvil types. NC State adds the ratchet style, lengths of about 20 to 40 inches, and telescoping handles. Gears and ratchets add weight and cost.

Hedge shears

Hedge shears, manual or electric, shear formal hedges to a set size and shape (Iowa State). Maryland limits hedge clippers to hedges and describes them as built for clean straight cuts.

Hand saws

Pruning saw

Iowa State sets pruning saws apart from the hacksaws and hand saws in a store's tool department. A pruning saw has a narrow, tapered or curved blade, and many have teeth set to cut on both the push and the pull. NC State lists curved and straight blades, a hooked end, and blades that cut only on the pull stroke, sold as turbo, tri-edge or three-angled. Those have three-beveled teeth. Some saws carry fine teeth at the tip and coarse teeth at the back. NC State also lists the scabbard, or sheath, that protects the blade.

Folding saw

Folding pruning saws are easy to carry safely, Iowa State notes. A maker's page from FELCO North America describes its folding saws as having a blade that locks in place when open. FELCO lists four folding models with these declared sizes.

FELCO folding pruning saws, maker's declared length and weight
ModelLengthWeight
6017.09 in0.31 lb
6028.66 in0.35 lb
60310.24 in0.47 lb
60411.81 in0.55 lb

Bow saw

A bow saw, in NC State's words, has a straight, sharp, quick-cutting blade. Most people do not use one for pruning because the shape blocks tight branch unions, and it suits downed wood, debris and firewood.

Pole tools

Pole pruner

Iowa State describes a stationary hook and a hinged blade worked by a rope, mounted on a long wooden or fibreglass pole. Maryland describes a hooked blade with a straight blade beneath it, moved by a rope pulled downward.

Pole saw

A pole saw is essentially a saw blade on a long pole (Iowa State). NC State shows one with a curved bottom blade for the undercut, and notes that combined saw and pruner heads are much heavier.

Pole material

Maryland puts fibreglass and plastic poles as lighter than wooden ones and, unlike aluminum, nonconductive. NC State says dielectric fibreglass poles made for tree clearance work do not conduct electricity, and aluminum poles often carry a nonconductive hand grip. Work near electrical lines needs special training and certification.

Chainsaws

Professional arborists often use chainsaws on large branches, and Iowa State calls them extremely dangerous in unskilled hands. Gas, electric and battery models all exist. NC State ties a chainsaw to proper training and personal protective equipment such as eye and hearing protection, chaps, head protection and steel-toed boots. OSHA's rules for chain saws in logging, 29 CFR 1910.266(e)(2), require a chain brake and ANSI B175.1-1991 compliance for saws placed in service after the effective date. Regulators' pre-start lists are set out in chainsaw pre-use checks by regulator.

OSHA rules for hand tools

OSHA 1910.266(e)(1) covers each hand and portable powered tool, including one the worker owns. The employer must keep it in serviceable condition and inspect it before first use each workshift. The inspection list names handles and guards, controls, cutting edges that are sharp and properly shaped, and the heads of impact tools, which must show no mushrooming. A chipping head is repaired or removed from service. Each tool is used only for what it was designed for. Other tool names are in the glossary of saws and cutting terms.

Sources