ArbNation Join free

Growing degree days: thresholds, calculation methods and the NEWA calculator

A degree day is one day with the temperature one degree above an organism's lower threshold. UC IPM sets out the sine, triangle and cutoff methods, and the NEWA calculator at Cornell lets users pick a base and a formula.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

UC IPM, the University of California's integrated pest management program, explains degree days on a concepts page. The page is marked as archived content, revised June 21, 2016. NEWA, the Network for Environment and Weather Applications, runs a degree day calculator on station data. Extension timing tables for tree pests are covered in the guide to degree days and indicator plants.

Thresholds and what a degree day counts

UC IPM says temperature controls the developmental rate of plants and invertebrates, including insects and nematodes. The accumulated heat an organism needs to go from one point in its life cycle to another is called physiological time. Degree days approximate it.

The lower developmental threshold is the temperature below which development stops. UC IPM says the organism's physiology sets it, whatever calculation method is used. The upper threshold is the temperature above which the rate of development begins to decrease or stop. How that is read depends on the cutoff method.

UC IPM gives San Jose scale as an example, with a lower threshold of 51°F and an upper threshold of 90°F. One degree day is one 24-hour day with the temperature one degree above the lower threshold. A scale held at 52°F for 24 hours therefore earns one degree day.

Celsius and Fahrenheit degree days are not interchangeable. Nine Fahrenheit degree days make five Celsius ones. UC IPM adds that degree hours need hourly temperatures, and that multiplying degree days by 24 only approximates them.

Biofix and accumulation

Each stage of an organism has its own total heat requirement. Accumulation starts at the biofix date, which UC IPM says varies with the species. Biofix dates usually rest on a biological event such as a planting date, the first trap catch or the first occurrence of a pest.

Calculation methods

All the methods turn a day's minimum and maximum temperatures into an estimate of the heat between the thresholds. UC IPM calls every one of them an approximation and says most are adequate for the precision that crop management decisions need. It says the method used to build an organism's growth relationships is the method to use. Where that method is unknown, UC IPM uses the single sine method with a horizontal cutoff at the upper threshold, because it has been the most common in California.

MethodHow UC IPM describes it
Single triangleOne triangle is fitted to the day's minimum and maximum. The curve is taken as symmetrical around the maximum.
Double triangleTwo half-day triangles are fitted, using the next day's minimum for the second. The two halves are added.
Single sineOne sine curve is fitted to the day's minimum and maximum. Degree days are the area above the threshold and under the curve.
Double sineTwo sine curves are fitted, from minimum to maximum and from maximum to the next day's minimum. The two halves are added.
Huber'sThe single sine result with a horizontal cutoff, less 0.3 Fahrenheit degree days when the day's minimum and maximum both fall between the thresholds. UC IPM notes its use in cotton pest management in the desert southwest.

UC IPM calls all of these linear methods, because development is taken as a straight-line function of temperature. It says nonlinear methods exist and are mostly used in research.

Cutoff at the upper threshold

The sine and triangle methods can be paired with three cutoffs. A horizontal cutoff assumes development continues at a constant rate above the upper threshold. The area above the upper threshold is subtracted once.

An intermediate cutoff assumes development slows but does not stop. The area above the upper threshold is subtracted twice. A vertical cutoff assumes no development at all above the upper threshold.

The NEWA degree day calculator

NEWA describes its tools as weather and science driven integrated pest management forecasts. Users start by choosing the nearest weather station. The degree day calculator returns results for all the base temperatures used in NEWA tools, from physical weather station data.

The user picks a location, a date range, a base temperature and a formula. The tool returns accumulated degree days and a chart of the accumulation over time. It focuses on recent data and includes the 5-day forecast. The calculator page opens with a base of 39°F.

The NEWA calculator page does not name the single sine or horizontal cutoff methods. A NEWA profile stores biofix details, and the page also points to a degree day calculator from Cornell Climate Smart Farming.

Sources