ArbNation Join free

Hand filing a saw chain: what makers publish about files, guides and depth gauges

Saw makers publish hand filing as a round file at about 30 degrees, a flat file for the depth gauge and a filing aid to hold the angle. WorkSafe Western Australia adds a sharpen at each refuel.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page draws on sharpening guides from saw makers and on WorkSafe Western Australia. It is not training and does not teach the work.

Tools and set-up as the guides list them

A maker's US guide lists the materials: a round saw chain file, a file angle plate, a flat saw chain file, a filing gauge, a felt tip pen and work gloves. A 2 in 1 filing guide is optional. The same guide has the chain cleaned and checked for damage, tensioned a little so the teeth can be sharpened more effectively, and held snug on the bottom of the bar rail with the bar in a vise.

The maker's UK blog adds two points. For a battery or electric saw, the battery is removed or the saw unplugged before sharpening, and the chain brake is released so the chain moves freely. Dust is brushed off the chain with a soft brush. The blog names five file sizes, chosen by the pitch of the chain.

The maker's Australian guide says the correct round file diameter follows the chain pitch. Its chains carry a marking on the depth gauge that shows the recommended round file diameter. The guide also points to the saw's operating instructions for maintenance work such as sharpening.

The cutter stroke

Hand filing points from the makers' guides
PointPublishedSource
Master toothOne tooth marked with a pen as the measure for all the others. If the wear marking is already reached, the chain is replacedMaker, US guide
StrokeThe file passes the tooth in forward strokes, from the inside outward, and lifts off on the backstroke. The file turns at regular intervals to avoid one-sided wearMaker, US guide
File positionThe file sits at 90 degrees to the guide rail, with a quarter of the file diameter above the top of the toothMaker, US guide
AngleAround 30 degrees. A file angle plate has markings for the correct angleMaker, Australian guide
When the edge is doneLight reflecting from the cutting edge means the tooth is not yet sharpMaker, US guide
Both sidesAll teeth on one side are filed to the same length as the master tooth. The saw is turned 180 degrees and the other side followsMaker, US guide
Stroke countEqual strokes on each cutter in most cases, with the teeth measured afterward to check they are close to identicalMaker, US guide
EvennessCorrect file size and both sides sharpened evenly. Equal angles on both sidesSecond maker, UK article

The depth gauge

The US guide says cutters get shorter in height as they are sharpened, so the depth gauge clearance shrinks and often needs an adjustment. The depth gauge setting is checked with the filing gauge that matches the chain pitch. If the depth gauge protrudes beyond the gauge, it is worked down horizontally with the flat file until flush. Humped drive links are worked at the same time. The top of the depth gauge is then filed at an angle parallel to the service marking, without lowering its highest point any further. The guide says a depth gauge set too low increases kickback.

The Australian guide defines the setting as the distance between the leading edge of the top of the tooth and the top edge of the depth gauge: the greater the distance, the more wood is planed per tooth. It says the setting must be checked and adjusted every time the chain is sharpened. The UK blog gives the reason from the other side: with the depth gauge left alone, the chain takes less and less wood out each time.

Filing aids and the regulator

The Australian guide says maintaining every angle and dimension freehand is very difficult and takes a lot of practice, and recommends filing aids. The 2 in 1 filing guide sharpens the teeth and sets the depth gauge in one pass. WorkSafe Western Australia (updated April 1, 2025) lists a file and file guide among the items near the work, with the chain sharpened and bar oil topped up each time the operator stops to refuel. It sets the depth gauge to the maker's recommendations in the operator's manual, and has the saw refueled only after the motor has cooled, for example after re-sharpening.

The guide to chain pitch, gauge and file size by maker has the file diameters. The guide to reading a dull or damaged chain tables the signs that a chain needs filing.

Sources