Hand tool safety rules: what OSHA and HSE print about the condition and use of hand tools
OSHA's general rule makes the employer responsible for the safe condition of hand tools, including tools workers bring themselves. Its logging rule adds a start-of-shift inspection list, and HSE's PUWER covers any tool used at work.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. The wording below comes from two OSHA sections, 29 CFR 1910.242 and 29 CFR 1910.266, and from HSE's pages on the Provision and Use of Work Equipment Regulations 1998 (PUWER).
OSHA 1910.242: hand and portable powered tools, general
Paragraph (a) of 29 CFR 1910.242 makes each employer responsible for the safe condition of tools and equipment used by employees. That includes tools and equipment the employees furnish themselves. Paragraph (b) covers compressed air used for cleaning: it is allowed only when reduced to less than 30 p.s.i. and then only with effective chip guarding and personal protective equipment.
The section is short and names no particular tool.
OSHA 1910.266: the logging rule on tools
Paragraph (e)(1) of 29 CFR 1910.266 sets out general requirements for hand and portable powered tools in logging operations. The standard defines logging operations as work associated with felling and moving trees and logs from the stump to the point of delivery, and the definition lists marking danger trees, felling, limbing, bucking, debarking and chipping. Its scope paragraph covers all types of logging whatever the end use of the wood. How OSHA treats tree care under it is covered in the guide to OSHA's status for tree care.
The employer must assure that each hand and portable powered tool, including any tool an employee provides, is maintained in serviceable condition. It must also assure that each tool is inspected before initial use during each workshift. The inspection covers at a minimum the items in the table.
| Paragraph | What the inspection assures |
|---|---|
| (e)(1)(ii)(A) | Handles and guards are sound, tight-fitting, properly shaped, free of splinters and sharp edges, and in place |
| (e)(1)(ii)(B) | Controls function properly |
| (e)(1)(ii)(C) | Chain-saw chains are properly adjusted |
| (e)(1)(ii)(D) | Chain-saw mufflers are operational and in place |
| (e)(1)(ii)(E) | Chain brakes and nose shielding devices are in place and function properly |
| (e)(1)(ii)(F) | Heads of shock, impact-driven and driving tools show no mushrooming |
| (e)(1)(ii)(G) | Cutting edges are sharp and properly shaped |
| (e)(1)(ii)(H) | All other safety devices are in place and function properly |
Further paragraphs set what the employer must assure about use and care. Each tool is used only for the purposes for which it was designed. When the head of a shock, impact-driven or driving tool begins to chip, the tool is repaired or removed from service. A cutting edge is sharpened to the maker's specifications whenever it becomes dull during the workshift. Each tool is stored in the provided location when not in use at a work site. Racks, boxes, holsters or other means are provided, arranged and used to carry tools so that no hazard is created for a vehicle operator or passenger.
The same section has its own paragraphs for chain saws, covering the chain brake, the continuous pressure throttle and the starting rules. Those are set out in the guide to chainsaw checks by regulator.
Great Britain: PUWER
HSE's PUWER overview says the regulations place duties on people and companies who own, operate or have control over work equipment, and on businesses whose employees use equipment, whether owned by them or not. Work equipment is any machinery, appliance, apparatus, tool or installation for use at work. HSE adds that this includes equipment employees provide for their own use at work, and that the use of work equipment covers starting, stopping, transporting, repairing, modifying, maintaining, servicing and cleaning.
The overview lists what PUWER requires of equipment provided for use at work. It is suitable for the intended use. It is safe for use, maintained in a safe condition and inspected to confirm it is correctly installed and does not subsequently deteriorate. It is used only by people who have received adequate information, instruction and training. It comes with suitable health and safety measures such as protective devices and controls, which will normally include guarding, emergency stop devices and visible markings.
Several of the listed duties bear on hand tools and powered hand tools. Equipment is maintained in an efficient state, in efficient working order and in good repair. Where it is exposed to deteriorating conditions liable to result in dangerous situations, it is inspected so faults are detected in good time. People who use, supervise or manage its use receive adequate training, which should include correct use, the risks and the precautions. Where use involves a specific risk, use is restricted to people trained and appointed to use it.
The PUWER Approved Code of Practice and guidance supports the regulations. HSE's overview quotes the Code's introduction: following the guidance is not compulsory, but anyone who does follow it will normally be doing enough to comply with the law. HSE's PUWER index page also links separate pages on inspection, maintenance, and training and competence.
Two systems side by side
| Question | OSHA 1910.242 and 1910.266(e)(1) | HSE PUWER overview |
|---|---|---|
| Who is responsible | The employer | Those who own, operate or control work equipment, and businesses whose employees use it |
| Tools the worker owns | Covered, in both sections | Covered: equipment employees provide for their own use at work |
| Inspection | Before initial use during each workshift, in logging operations | Where equipment is exposed to deteriorating conditions, inspected so faults are detected in good time |
| Named defects | Mushrooming heads, chipped heads, dull or misshapen cutting edges, loose or splintered handles | None named for hand tools |
| Training | Not in these paragraphs | Adequate information, instruction and training for users, supervisors and managers |
Sources
- OSHA, 29 CFR 1910.242 Hand and portable powered tools and equipment, general, eCFR current text, read October 16, 2026
- OSHA, 29 CFR 1910.266 Logging operations, paragraphs (b), (c) and (e)(1), eCFR current text, read October 16, 2026
- HSE, Provision and Use of Work Equipment Regulations 1998 (PUWER), overview (updated November 21, 2024), read October 16, 2026
- HSE, Provision and Use of Work Equipment Regulations 1998 (PUWER), index page (updated March 16, 2023), read October 16, 2026