ArbNation Join free

Hauling logs and firewood: 49 CFR 393.116 and the Australian and UK log guidance

Section 393.116 of the US federal rules is the log-specific cargo securement section. It sends firewood and short logs to a vehicle or container enclosed on both sides, front and rear, and sets tiedown and stake rules for longer logs.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. The US text is 49 CFR 393.116, Specific securement requirements for logs, from the Electronic Code of Federal Regulations. The section was last amended on June 22, 2006. Sections 393.100 through 393.114 appear in load securement in the United States.

Covered loads and exceptions

Paragraph (a) applies the section to the transport of logs and lists three exceptions. Each sends the load to the general cargo rules or to a different container rule.

  • Logs unitized by banding or comparable means may follow the general cargo rules in sections 393.100 through 393.114.
  • Loads of no more than four processed logs may follow the same general rules.
  • Firewood, stumps, log debris and other short logs must travel in a vehicle or container enclosed on both sides, front and rear and strong enough to contain them. Longer logs may also be loaded that way.

The securement system

Paragraph (b) says logs must travel on a vehicle designed and built, or adapted, for logs. It must have bunks, bolsters, stakes or standards, or an equivalent, that cradle the logs and stop them rolling. Parts that secure logs must withstand all anticipated operating forces without failure, accidental release or permanent deformation. Stakes that are not permanently attached must be secured against separating in transit.

Tiedowns are used together with bunks, stakes and bolsters. The one exception is a crib-type log trailer, as defined in 49 CFR 393.5, loaded in line with paragraphs (b)(2) and (c). On a frame vehicle or a flatbed with bunks, bolsters or stakes, the aggregate working load limit of the tiedowns for a stack must be at least one-sixth of the stack's weight.

Loading rules for every stack

Paragraph (c) sets four rules. Logs must be solidly packed, and the outer bottom logs must rest against the bunks, bolsters, stakes or standards. Each outside log on a side must touch at least two stakes, bunks, bolsters or standards. The centre of the highest outside log on each side or end must sit below the top of each stake, bunk or standard. Any log not held by other logs or by the stakes must be held by a tiedown, and more tiedowns are required when low friction between logs makes slipping likely.

Shortwood loaded crosswise

Paragraph (d) adds rules for shortwood stacked crosswise on frame, rail and flatbed vehicles.

  • A log end in the lower tier may not extend more than one-third of the log's length past the nearest support.
  • A single stack needs at least two tiedowns, attached to the frame at the front and rear of the load and crossing the load. When two are used, they sit at about one-third and two-thirds of the log length.
  • A vehicle over 10 metres (33 feet) long needs centre stakes or a comparable device to divide it into sections of about equal length.
  • Two stacks loaded next to each other must have no space between them. The outside of each stack must be raised at least 2.5 cm (1 inch) within 10 cm (4 inches) of the log ends or the vehicle side. The highest log may be no more than 2.44 m (8 feet) above the deck. At least one tiedown runs lengthwise across each stack.

Logs loaded lengthwise and on pole trailers

Paragraph (e) covers lengthwise loads on flatbed and frame vehicles. Shortwood must be cradled in a bunk unit or held by stakes, and secured by at least two tiedowns. One tiedown is enough when every log in the stack is blocked at the front by a strong structure or another stack and at the rear by another stack or the vehicle end structure. A tiedown used alone must sit about midway between the stakes. Two wrappers that encircle the whole load are the third option.

Longwood must sit in two or more bunks. It needs at least two tiedowns or two wrappers around the load.

Paragraph (f) covers pole trailers. The load needs at least one tiedown at each bunk, or at least two wrappers. The front and rear wrappers must be at least 3.04 metres (10 feet) apart. Large single and double log loads must be immobilized with chock blocks or an equivalent. Large logs that rise above the bunks need at least two more wrappers to the load beneath.

Australia: the Load Restraint Guide

The National Heavy Vehicle Regulator publishes the Load Restraint Guide 2025, its fourth edition. The logs section describes its guidelines as one way to meet the Performance Standards. They are a guide only, and other methods are allowed. The guide recommends an engineer certify alternative methods. Restraint depends on whether the logs are pulp or saw logs, long or short, and with bark on or off. The guide treats debarked logs with high sap content as low-friction.

For loose logs between stanchions, the guide lists these points:

  • Every log is restrained to stop it sliding out of the pack, with more restraints for low-friction logs.
  • Each log is held by at least two stanchions on each side of the load.
  • Log lengths extend at least 300 mm beyond the outer stanchions, forward and rearward, where lashings alone do not restrain the logs.
  • Longer logs go towards the outside of the stack and shorter logs in the centre.
  • Webbing straps are tensioned on both sides where practical and safe, because a strap tensioned on one side loses tension through friction.
  • Loads are crowned so every log is clamped by the tie-down lashings. The top logs of the crown do not rise more than half their height above the stanchions.

On the road, the guide calls for regular checks of lashings and load position, with re-tensioning as required. Loads can settle in transit, particularly when leaving the coupe, the section of forest being harvested.

United Kingdom: the securing loads guidance

The GOV.UK guidance on securing loads on HGVs and goods vehicles has a timber heading. It says timber loads must be secured to the vehicle. Prepared timber is secured with lashings or chains, and long lengths usually need three straps rather than two so the load does not rotate. Rope must not be the primary method. The guidance names chains, with extra side support from goal posts, as the best method for uncut timber, and points to the Timber Transport Forum's good practice guides.

The three sources print no state or national weight tolerance for forest products, so none appears here.

Sources