ArbNation Join free

Inspecting lanyards and flip lines: what the codes require

SafeWork NSW says lanyard webbing should be retired if it has any visible cut. WorkSafe NZ sets a check before each use. The UK ICoP gives lanyard performance rules and sends inspection to the maker.

Checked against the sources at the bottom of this page on October 19, 2026. Rules, fees and pay change: the source has the last word.

The named codes and training bodies are described here as published. It is not training and does not teach the work. The harness, rope and connector pages in the same family are listed under gear inspection rules.

Credits: SafeWork NSW text is summarised from the Tree works code of practice (March 2026), copyright State of New South Wales (SafeWork NSW), licensed under Creative Commons Attribution 4.0; changes were made, because the text is summarised and reworded. WorkSafe New Zealand material is summarised from its Approved Code of Practice for Safety and Health in Arboriculture, with the source acknowledged.

Code by code

Inspection and removal wording for adjustable lanyards and flip lines
SourceWording
SafeWork NSW code, 4.5, New South WalesFor adjustable lanyards the code lists points to consider in selecting, using and maintaining them. Webbing should be retired if there are any visible cuts. Faulty, defective or visibly worn or cut rope lanyards should not be used and should be permanently removed from service. Wire or wire core lanyards should not be used in an electrical environment. Lanyards should incorporate a maximum length stop as an integral part.
SafeWork NSW code, climbing equipment, New South WalesThe climber should thoroughly inspect climbing equipment before and after each use. Damaged equipment should be removed from service until assessed by a competent person.
WorkSafe NZ code, 3.2, New ZealandArborists check climbing lines, work lines, lanyards and other climbing equipment for damage, cuts, abrasion or deterioration before each use. They remove it from service if signs of excessive wear or damage are found. A safety lanyard, which the code also calls a strop or flip line, must meet the minimum strength requirements of an arborist climbing line.
ICoP 3.10.6.10 and 3.11, United KingdomA lanyard in a personal fall protection system must suit its connectors, adjust reliably under load, attach to the harness without torsion or cross-loading, and have a minimum breaking strength of at least 15 kN. Inspection follows the maker's information, and defective items should be withdrawn from service.

What the UK code leaves to the maker

The Arboricultural Association ICoP lists no lanyard defect checklist. Section 3.11.2 says how far any damage affects a component depends on its material and construction, and refers to the information supplied with the equipment or the advice of the maker. Items that are defective, or show symptoms that could lead to a defect in use, should be withdrawn from service. Whoever carries out pre-use checks or interim inspections should be able to detect defects and remove an item from service.

Under the Lifting Operations and Lifting Equipment Regulations, the ICoP says equipment used for lifting people is thoroughly examined at least every 6 months. Records of inspections should be kept at least until subsequent inspections take place.

New Zealand rules on use that bear on inspection

The WorkSafe NZ code says the safety lanyard is never unclipped except to bypass branches. A second lanyard or line is fastened free of the obstructing branch and checked before the first is unclipped. Lanyards should have an effective means to stop a friction hitch slipping off the end. Snap hooks used in the climbing system are rated at or above 22 kN and are auto-locking.

The code also bars strops or flip lines that contain metal within the vegetation management zone near power lines. It says no climbing equipment is to be marked for identification, for example by engraving, or altered in a way that undermines its structural integrity.

Tool lanyards

The SafeWork NSW code treats the chainsaw tool lanyard separately. It should be long enough to allow full reach and for the chainsaw to hang below the climber's feet when not in use. Connection hardware that forms part of it should be marked with a load rating and be auto locking with three consecutive actions to open. It should incorporate a weak link that allows it to be separated from the harness in the event of extreme loading.

Standards named

EN 354:2010 specifies requirements, test methods, marking, maker information and packaging for lanyards used as connecting elements in restraint, work positioning, rope access, fall arrest and rescue systems. EN 358:2018 applies to belts and lanyards for work positioning or restraint. It does not cover fixed-length restraint lanyards that are not integrated into a belt, which EN 354 covers. The ICoP lists both in its standards.

Sources