ArbNation Join free

Ladders and tree steps in tree work: OSHA 1910.23, OSHA's tree care page, OSHA 3979 and the USFS guide

OSHA lists 29 CFR 1910.23 among the general industry rules that reach tree care. The US Forest Service guide names the Swedish sectional ladder as the type most suited to climbing and sets its own wording on tree steps.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. Everything below is what the named codes and training bodies publish. It is not training and does not teach the work.

OSHA's tree care standards page

OSHA's tree care page states that the tree care industry must comply with all the general industry standards in 29 CFR 1910. Under Subpart D, Walking-Working Surfaces, it lists 1910.21 scope and definitions, 1910.22 general requirements, 1910.23 ladders, 1910.25 stairways, 1910.26 dockboards, 1910.29 fall protection systems and 1910.30 training requirements. It does not list the construction ladder rule, 1926.1053, which is covered in the guide to ladder rules for tree work.

OSHA also lists voluntary ANSI standards that may apply to tree care. It states that meeting them does not guarantee meeting OSHA policy. Three concern ladders: A14.1 portable wood ladders, A14.2 portable metal ladders and A14.5 stepladders and platform ladders in aluminum, magnesium and fiberglass.

29 CFR 1910.23, the general requirements

Section 1910.23 covers all ladders except those used in emergency operations such as firefighting and rescue, and those built into machines or equipment. Paragraph (b) puts these duties on the employer for every ladder.

  • Rungs, steps and cleats are parallel, level and evenly spaced, 10 to 14 inches apart between centrelines on most ladders, with a minimum clear width of 11.5 inches on portable ladders.
  • Wooden ladders are not coated with anything that could hide structural defects, and metal ladders resist corrosion.
  • Ladders are used only for the purposes they were designed for.
  • Ladders are inspected before first use in each work shift, and more often as needed. A defective ladder is tagged "Dangerous: Do Not Use" and removed from service until repaired or replaced.
  • Each employee faces the ladder, uses at least one hand to grasp it and carries no load that could cause a fall.

Paragraph (c) adds rules for portable ladders. Loads stay within the maximum intended load, which the rule's note defines to include the employee and all tools, equipment and materials carried. Ladders stand on stable and level surfaces unless secured or stabilised. No single rail ladders are used, and none is moved, shifted or extended while someone is on it. On slippery surfaces they are secured and stabilised. Side rails reach at least 3 feet (0.9 m) above an upper landing. Ladders are not tied together for length unless made for it, and not set on boxes or barrels for height.

OSHA 3979 on power lines

OSHA publication 3979, Working Safely Near Overhead Power Lines (2019), lists practical steps against contact. They are a hazard assessment, asking the electric company to de-energize and ground the lines, training, knowing the safe working distance, non-conductive wood or fiberglass ladders, and personal protective equipment such as rubber insulating gloves. The wording on ladders is that single line.

The US Forest Service guide, section 5.2

The Forest Service's National Tree Climbing Guide (2015) says the ladder most suitable for tree climbing is the Swedish sectional tree climbing ladder or an equivalent design. Other stacking ladders are not as secure, it says, which raises the chance of injury. Metal ladders carry electrical hazard labels reading "Warning, Do Not Use Around Electrical Equipment."

HeadingWhat the guide lists
5.2.1 UsesGeneral tree work in larger trees; whenever more than one person must go up or many ascents are needed
5.2.2 AdvantagesEasy to use and reusable until the job ends; easy access into the live crown; access to trees whose boles are easily damaged by other climbing methods; access into small trees
5.2.3 DisadvantagesCost compared with other access methods; strain or a falling hazard to the ground crew if the ladder gets away during setup; hard to pack over steep or brushy ground
5.2.4 UseNo climbing wet or iced ladders; rubber or neoprene soles; sections secured to the bole by chain or strap before climbing without a lanyard; no breaking off dead branches with ladder sections; no ladders left unattended in trees
5.2.5 CareDry indoor storage, dirt and pitch removed, electrical warnings kept legible, inspection of rungs, rails, screws, nuts, bolts, chains, turnbuckles and ratchet straps before each use, padding when transported

A pulley haul system, the guide says, can raise and lower ladder sections once the climber is above two mounted sections. Section 8.2 of the same guide covers rescue from sectional ladders, with a minimum gear list of a rappel system, four locking carabiners, gloves, rescue rope, two lanyards and bolt cutters.

Tree steps, section 5.6

The guide defines tree steps as lightweight metal platforms with a length of chain that attaches to the bole. It says a lanyard must be used at all times when tree steps support the climber. Their uses are bridging gaps between live branches, giving access to the live crown and acting as a temporary working platform. Steps are placed no more than 24 inches apart on one side of the bole, or 12 inches apart when staggered. Inspection for metal fatigue is called the most critical maintenance, and steps showing fatigue on the platform are discarded.

The guide's section on ascent also names tree steps, or webbing slings, as an option on trees with upward-sloping branches that would otherwise trap the feet.

Sources