Lanyards in tree work: flip lines, wire-core and adjustable lanyards by type and standard
The codes describe fixed and adjustable lanyards, and call the work positioning lanyard a flip line. NSW says wire and wire core lanyards should not be used in an electrical environment, and EN 358:2018 covers work positioning belts and lanyards.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
Lanyards in tree work are described below as the UK industry code, SafeWork NSW, WorkSafe New Zealand and the European standard's scope page publish them. It is not training and does not teach the work.
The kinds of lanyard
The Industry Code of Practice for Arboriculture: Tree Work at Height, Edition 2, May 2020, defines a lanyard as a short, adjustable system that connects to an anchor. Clause 3.10.6.10 says lanyards can be fixed or adjustable. The code prefers the adjustable kind in the most common use, because it minimises slack and so the distance and consequences of a fall.
WorkSafe New Zealand defines a safety lanyard, also called a strop or flip line, as an adjustable rope or strop made as a work positioning aid. All its materials must meet the minimum strength of an arborist climbing line. The code adds that friction hitches and work-positioning lanyards used in a climbing system must meet the minimum strength standards for arborist climbing lines.
Adjustable lanyards
The UK code lists what a lanyard in a personal fall protection system must be. It must be compatible with the connectors in use, have a means of adjustment and a suitable length, and adjust efficiently, positively and reliably under load. It must be attached to the harness so as to prevent torsion or cross-loading, and have a minimum breaking strength of at least 15 kN.
SafeWork NSW section 4.5, Adjustable lanyards, lists five points for selecting, using and maintaining them:
- Wire or wire core lanyards should not be used in an electrical environment.
- The orientation of the connection hardware should not encourage twisting or roll out.
- Webbing should be retired if there are any visible cuts.
- Lanyards should have a maximum length stop as an integral part.
- Faulty, defective or visibly worn or cut rope lanyards are removed from service permanently.
The NSW code says the work positioning harness should be used with adjustable lanyards or pole straps. It limits that harness to situations that may give a restrained fall or a limited free fall, and not where a free fall of more than 600 mm is possible. Section 4.8 says climbing spikes should be used with a fall prevention system of a work positioning harness and adjustable lanyards.
Metal in lanyards near power lines
NSW says wire and wire core lanyards should not be used in an electrical environment. The WorkSafe New Zealand code has a similar concern in two statements. In it, arborists shall not use metal-handled pruners or tools, metal ladders, or strops or flip lines containing metal within the vegetation management zone around power lines, or on any tree extending into it. Wire ropes or strops are also barred within four metres of any power line.
Rules for lanyards on the tree
The New Zealand code covers use of the safety lanyard directly. It says that when climbing, the safety lanyard shall never be unclipped except to bypass branches. In that case a second safety lanyard or line shall be fastened free of the obstructing branch and checked for security before the first lanyard is unclipped. Lanyards should have an effective means to stop the friction hitch or device slipping off the end. Snap hooks used as lanyard clips shall be rated at or above 22 kN and be auto-locking, needing a minimum of three distinct movements to open.
The NSW code treats tool lanyards separately. A chainsaw tool lanyard should reach far enough for the saw to hang below the climber's feet. Its connection hardware should be marked with a load rating and be auto-locking, with three consecutive actions to open it. It should include a weak link that lets it separate from the harness under extreme loading.
EN 358 and the related standards
The Estonian standards body lists EVS-EN 358:2018, Personal protective equipment for work positioning and prevention of falls from a height. Belts and lanyards for work positioning or restraint. It was valid from 19 December 2018, follows the 2000 edition in the standard history and is listed under PPE Regulation 2016/425.
The scope text covers belts and lanyards for work positioning or restraint, and sets requirements, testing, marking and the information the maker supplies. It leaves out fixed-length restraint lanyards not integrated into a belt, which EN 354 covers. The UK code's list of work equipment standards also carries BS EN 354 for lanyards, BS EN 355 for energy absorbers and BS EN 12841 for rope adjustment devices.
Sources
- EVS, the Estonian standards body, EVS-EN 358:2018 scope and standard history, read October 16, 2026
- SafeWork NSW, Tree works code of practice, March 2026, sections 4.4, 4.5, 4.8 and chainsaw tool lanyards, read October 16, 2026
- WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture, November 2012, read October 16, 2026
- Arboricultural Association and partners, Industry Code of Practice for Arboriculture: Tree Work at Height, Edition 2, May 2020, clause 3.10.6.10 and Part 6, read October 16, 2026