ArbNation Join free

Large tree transplanting: root-ball formulas and sizes used by A300 Part 6 and ANSI Z60.1

ANSI A300 Part 6 covers root ball sizing and four transplanting methods, and ANSI Z60.1 holds the nursery stock root-ball tables. Utah State and Missouri extension print example sizes: a 3-inch tree at 30 to 36 inches, a 2-inch maple at 24.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here. It describes what the named standards and extension publications say about root balls. It is not training and does not teach the work. The tables of ANSI A300 and ANSI Z60.1 are copyrighted and are not reproduced, so the only sizes here are examples printed by extension services. Moving a tree with a spade has its own page.

A300 Part 6

The Tree Care Industry Association says Part 6 of the A300 standards applies to planting and transplanting trees, shrubs, palms and other woody plants. Its topic list includes plant and site inspection, timing of transplanting, determining the root ball size for transplanting, digging, lifting, moving and storage, digging the planting hole, planting container stock, palm standards and post-planting care.

TCIA lists four basic transplanting methods that the A300 transplanting standards recognize.

Transplanting methods named in A300 Part 6
MethodTCIA description
Balled and wrappedPlants established in the ground and prepared by digging so the soil immediately around the roots stays undisturbed. The ball of earth with the roots is then bound up.
Bare rootHarvested plants from which the soil or growing medium has been removed.
BoxedA method of protecting roots that includes digging a trench, building and installing a box around the roots, and using the box to lift, transport and install the plant.
Tree spadeEquipment used to transplant large trees.

TCIA also prints an advisory notice that the correct planting depth is based on locating the trunk flare, with the bottom of the flare at finish grade on completion.

ANSI Z60.1

ANSI Z60.1 is the American Standard for Nursery Stock, published by the American Nursery and Landscape Association (ANLA). The 2004 edition, approved May 12, 2004, is posted by the Indiana Department of Natural Resources, Division of Forestry. Its foreword says the Association has kept a standards committee since 1921, issued its first Horticultural Standards in 1923, and published its first edition under American Standards Association procedures on June 22, 1949. The 2004 revisions were developed by the Horticultural Standards Committee from January 1997 through May 2003 and sent to national and regional societies, companies, individuals and agencies for review and endorsement.

The 2004 contents list a Root ball guidelines section in each plant group. For shade and flowering trees the section headings are Root ball diameters for field grown trees, Trunk in center of root ball, Root ball depths, Burlapping and Ball-supporting devices. Separate headings give root ball diameters for shrub-form, clump-form and multi-stem trees. The diameters themselves are set in the standard's tables and are tied to the caliper of the tree, or to its height for small upright and small spreading types.

Sizes printed by extension services

The University of Missouri Extension guide G6879 cites ANLA standards for one example: a 2-inch-caliper red maple should have a soil ball about 24 inches in diameter and about 16 inches deep. Missouri adds that digging removes up to 95 percent of a tree's roots.

Utah State University Extension, in Planting Landscape Trees, gives a rule of thumb. The root system, root ball or container diameter should be 10 to 12 inches for every inch of stem caliper, measured at ground line just above any basal swell. A 3-inch caliper tree should therefore have a root ball at least 30 to 36 inches wide. Utah State adds that depth matters less than width but should be larger for larger trees. It lists four tree types: balled and burlapped, container, bare-root and tree-spaded. Its tree spade is a large machine that cuts roots and soil so the ball can be wrapped.

The Missouri figure works out to 12 inches of ball for each inch of caliper, which falls inside the Utah State range.

Sources