Moving timber by hand: the aid tools and wedges HSE, SafeWork NSW and WorkSafe NZ name
HSE names the aid tools for moving and felling timber in its chainsaw leaflet. SafeWork NSW and WorkSafe New Zealand name wedges and pulling gear in their tree codes, and OSHA defines a chock.
Checked against the sources at the bottom of this page on October 9, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. It does not describe how to use any tool or say that one tool replaces another. Saws have their own guide to chainsaw regulator pages by country, and the glossary of saws and cutting defines felling and cutting words.
HSE: the aid tools in the chainsaw leaflet
The Health and Safety Executive (HSE) leaflet INDG317, Chainsaws at work, revision 2 of January 2013, has a section on manual handling. Manual handling causes over a third of all workplace injuries, and employers must look at the risks of a task that cannot be avoided and use lifting aids where necessary. Under the heading "Aid tools" the leaflet names pulp hooks, log tongs and high lift wedges. Used correctly, they help operators do the job with a minimum of effort and with a straight back. Figure 3 shows five items: a breaker bar with cant hook, a log pick, high lift wedges, pulp hooks and log tongs.
On grip, the leaflet gives properly sharpened pulp hooks or log tongs as one of the best methods. They also preserve the operator's gloves and mean less bending, and both hands are used because one hand tends to twist the back. A log pick can be a useful handling tool in some situations. Under "Heavy loads", a portable winch is useful for applying large forces when felling large or awkward trees and for turning over a large tree stem. High lift wedges allow forces well in excess of those from a breaking bar. Felling cushions are available that can be used instead of wedges, and exhaust gas from the chainsaw inflates the cushion and forces the tree over.
The leaflet's felling section says operators may need aid tools such as alloy or plastic wedges, a breaking bar, a cant hook, a winch, or high-lift wedges and a sledgehammer.
SafeWork NSW: wedges in the Tree works code
The SafeWork NSW Tree works code of practice, which commenced on March 27, 2026, says suitable equipment such as wedges should be considered to prevent a tree falling in a direction other than the one intended. The controls for clear felling list wedges used as needed to assist the fall direction. The controlled directional felling controls say wedges may be used to assist, and ropes, cables and winches are rated appropriately for the expected loads. Before winching, lifting or lowering a load, the working load limit should be determined and observed.
WorkSafe New Zealand: the arboriculture code
The WorkSafe New Zealand approved code of practice Safety and health in arboriculture says that where the size of the tree being felled has the potential to cause harm, "wedges, block and tackle, rope, wire cable or other appropriate devices" shall be used. Wedges and driving tools should be readily available during all felling operations. A pulling line should be attached to all trees and stems being felled where assisted directional felling is required. WorkSafe notes that the code has not been updated to reflect the Health and Safety at Work Act 2015, and that it may contain relevant information.
The code's section on winches, wire ropes and accessories says hand winch, machine winch and hauling machine operators shall be competent in all facets of winching. Where two persons have applied the load to a hand winch handle or lever, two persons shall be used to release the load. When a stump is used as a ground anchor or to secure pulling blocks, it shall be of sufficient size and stability. Strops anchoring winches or pulling blocks shall be at least 1.5 times the safe working load of the pulling rope.
OSHA: the definition of a chock
The US logging standard, 29 CFR 1910.266, defines a chock as a block, often wedge shaped, used to prevent movement, for example a log from rolling or a wheel from turning. The standard uses the word for wind-thrown trees, where precautions before bucking or limbing include chocking or moving the tree to a stable position, and for trailer chippers on a slope. The standard's definitions list the chock but no cant hook or log tongs.
Names in each source
| Tool or aid | Named by |
|---|---|
| Breaker bar or breaking bar | HSE |
| Cant hook | HSE |
| Block and tackle | WorkSafe NZ |
| Chock | OSHA |
| Felling cushion | HSE |
| High lift wedge | HSE |
| Log pick | HSE |
| Log tongs | HSE |
| Pulp hook | HSE |
| Sledgehammer or driving tool | HSE (sledgehammer), WorkSafe NZ (driving tools) |
| Wedge, alloy or plastic | HSE, SafeWork NSW, WorkSafe NZ |
| Winch | HSE, SafeWork NSW, WorkSafe NZ |
Credits
Contains public sector information published by the Health and Safety Executive and licensed under the Open Government Licence v3.0. The SafeWork NSW Tree works code of practice is licensed under Creative Commons Attribution 4.0, and the passages here are in this page's own words. The WorkSafe New Zealand text is reported with credit to WorkSafe New Zealand.
Sources
- Health and Safety Executive, INDG317 Chainsaws at work, revision 2, January 2013, read October 9, 2026
- SafeWork NSW, Tree works code of practice, March 2026, read October 9, 2026
- WorkSafe New Zealand, Safety and health in arboriculture approved code of practice, read October 9, 2026
- OSHA, 29 CFR 1910.266 Logging operations, read October 9, 2026