Low-kickback chain and reduced-kickback bars: the features and the standards behind them
Low-kickback chain, a reduced-kickback bar and a chain brake are the saw-side features that HSE, CCOHS and extension services name against kickback. They reduce it and do not remove it.
Checked against the sources at the bottom of this page on October 15, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here. HSE, CCOHS, an extension service and two standards entries supply the facts below. It is not training and does not teach the work.
What kickback is
HSE's leaflet Chainsaws at work (INDG317) defines kickback as the sudden uncontrolled upward and backward movement of the chain and guide bar towards the operator. It can happen when the chain at the nose of the bar hits an object. HSE adds that kickback causes a significant share of chainsaw injuries, many to the face and upper body, where protection is hard to give.
CCOHS, the Canadian centre for occupational health and safety, quotes the definition in CSA Z62.3-11 (R2021). It names two kinds: rotational kickback, when the chain near the top of the bar nose touches a log or branch, and pinch kickback, when wood closes in and pinches the chain in the cut.
Features regulators and extension services name
| Feature | What the source records |
|---|---|
| Low-kickback chain (safety chain) | HSE's figure of a rear-handled chainsaw labels "chain with low-kickback characteristics" next to the chain catcher, the throttle trigger lockout and the rear chain breakage guard. The University of Missouri Extension guide G1959 says safety chain has features built to reduce kickback, such as a guard link |
| Reduced-kickback bar | In the Missouri guide, the tendency toward kickback grows with the radius of the bar nose. A smaller kickback zone can come from asymmetric nose bars, called "banana bars", which some makers offer. CCOHS lists "reduced kickback saw chain" in the same group of devices |
| Chain brake | On HSE's account, a properly maintained chain brake and low-kickback chain reduce the effect of kickback but cannot entirely prevent it. The Missouri guide describes the brake as built to stop the moving chain in a fraction of a second if kickback occurs |
| Bar nose cover | CCOHS mentions a safety tip that covers the nose of the bar. It is taken off for bore cuts and for wood thicker than the bar is long |
Labels and saw size
The Missouri guide links low-kickback chain to saw size. Consumer saws must come with low-kickback chain, and the guide gives the requirement for saws with an engine smaller than 3.8 cubic inches. Safety chain is available for larger saws too, and the guide calls it highly recommended there.
The guide reports a colour code on replacement chain. Chain with a blue label meets the low-kickback standard and can go on any saw. Chain with a yellow label is recommended for professional use only, although some yellow-label chain can go on certain saws under 3.8 cubic inches. The guide adds that larger professional saws may lack some of the safety features a buyer would want.
The same guide notes that the U.S. Consumer Product Safety Commission, working with ANSI B175.1, splits petrol saws at 3.8 cubic inches (62.3 cubic centimetres). Smaller saws are meant mainly for consumer use. Larger ones count as professional saws, and the two groups have different requirements.
Standards that name the devices
CCOHS lists kickback-reducing devices that are matched to the saw they sit on and meet standards such as CSA Z62.3-11 (R2021), Chain Saw Kickback, or ANSI B175.1-2021, the safety and environmental standard for hand-held internal-combustion chain saws. It adds that the devices reduce kickback and do not prevent it.
The ISO 11681 series covers the saw as a whole. The Estonian standards centre prints the scope of both parts, and they treat kickback differently.
| Standard | Saws covered | Kickback in the scope text |
|---|---|---|
| ISO 11681-1:2022 | Portable combustion-engine chain-saws for forest work, used by one operator with the right hand on the rear handle and the left on the front handle | All significant hazards are covered, with the exception of kickback and balance for machines with an engine displacement of more than 80 cm3 |
| ISO 11681-2:2022 | Portable combustion-engine chain-saws for tree service, with a maximum mass of 4,3 kg without bar and chain and with empty tanks, used by a trained operator | All significant hazards are covered, with no exception for kickback in the scope text |
Both parts apply to chain-saws made after the date of publication, and both leave dismantling and scrapping out. Missouri's 62.3 cubic centimetre split and ISO's 80 cm3 line are different figures from different documents.
For the brake side, see chainsaw kickback and chain brakes. The standards for other countries are listed in chainsaw standards by country.
Credit: the HSE statements are adapted from HSE publication INDG317, Crown copyright, used under the Open Government Licence v3.0.
Sources
- HSE, Chainsaws at work INDG317 (rev2, January 2013), read October 15, 2026
- University of Missouri Extension, Basic Chain Saw Safety and Use G1959, reviewed August 2011, read October 15, 2026
- CCOHS, Chainsaws - Kickback, fact sheet revised August 22, 2023, read October 15, 2026
- Estonian Centre for Standardisation and Accreditation, EVS-EN ISO 11681-1:2022 scope, read October 15, 2026
- Estonian Centre for Standardisation and Accreditation, EVS-EN ISO 11681-2:2022 scope, read October 15, 2026