Major axis, minor axis and gate-open strength markings: what the stamped kN figures mean
A carabiner maker prints three strength figures in kilonewtons: major axis, minor axis and open gate. This page sets one maker's declared figures beside the DMM markings page, the BSI standard scopes and the minimums in two tree codes.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
The New Zealand Approved Code of Practice for Safety and Health in Arboriculture defines the kilonewton (kN) as a unit used for the safety holding values of fasteners, anchors and climbing equipment. It gives a rule of thumb that 1 kN is approximately equal to 100 kilograms. The code defines a carabiner as a metal loop with a sprung or screwed gate used as a connector.
One maker's declared figures
Petzl's product page for the WILLIAM aluminum carabiner prints three strengths in one specification table. The figures are the same for all seven listed references, in three locking systems and three colours. Petzl lists the certifications as CE EN 362 and CE EN 12275 type B, among others.
| Strength as the page prints it | Declared figure |
|---|---|
| Major axis strength | 27 kN |
| Minor axis strength | 8 kN |
| Open gate strength | 8 kN |
| Gate opening | 27 mm (28 mm on the screw-lock references) |
Petzl's table prints the three strengths as separate rows and leaves the two axes undefined in words. The UK industry code uses the term major axis only in its connector requirement.
The DMM markings page
DMM Wales lists the general markings that can appear on its products. The page warns that markings differ with the product type, the standards and the room for marking.
- EN Standard: the European Standard or Standards the product was tested and certified to.
- CE0598: the CE marking; the number 0598 identifies the Notified Body for the PPE conformity assessment and production surveillance.
- MBS: Minimum Breaking Strength, the minimum load at which the product is expected to fail under laboratory testing conditions, stated in kilonewtons.
- WLL: Working Load Limit, the maximum load that may be applied in normal use as the maker specifies. DMM says it comes from the product strength and the safety factors that apply.
DMM defines MBS and WLL but not major axis, minor axis or open gate strength.
The standards behind the marks
BSI records BS EN 12275:2013 as a current standard on mountaineering equipment connectors. Its scope is safety requirements and test methods for connectors for mountaineering, climbing and related activities, as part of the system that protects the climber from a fall from height. BS EN 362:2004 is current too. Its scope is the requirements, test methods, marking and information supplied for connectors used as connecting elements in fall arrest, work positioning, rope access, restraint and rescue systems.
Minimums in two tree codes
The UK Industry Code of Practice for Arboriculture, Tree Work at Height, requires connectors to be configured so that only the major axis is loaded, where applicable. It also requires a minimum breaking strength of at least 22 kN. The New Zealand code requires all carabiners in a climbing system to be rated at or above 22 kN and to be auto-locking. It defines an auto-locking carabiner as one that locks on closing and needs a minimum of three distinct movements to open.
Sources
- Petzl, WILLIAM aluminum carabiner, professional product page and specifications, read October 16, 2026
- DMM Wales, Product Markings: explanation of general markings, read October 16, 2026
- BSI Knowledge, BS EN 12275:2013 Mountaineering equipment. Connectors. Safety requirements and test methods, read October 16, 2026
- BSI Knowledge, BS EN 362:2004 Personal protective equipment against falls from a height. Connectors, read October 16, 2026
- Arboricultural Association and partners, Industry Code of Practice for Arboriculture: Tree Work at Height, Edition 2, May 2020, read October 16, 2026
- WorkSafe New Zealand, Approved Code of Practice for Safety and Health in Arboriculture, November 2012, read October 16, 2026