Manual handling duties: Great Britain's 1992 Regulations, WorkSafeBC and OSHA
Great Britain's Manual Handling Operations Regulations 1992 put a three-step duty on employers: avoid, assess, reduce. WorkSafeBC's OHS Regulation sets ergonomics duties in sections 4.46 to 4.53.
Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.
This page reports what the official source says. It is not legal advice: ask the office named here.
Great Britain: the 1992 Regulations
Regulation 4 of the Manual Handling Operations Regulations 1992 sets the duties of employers. The first duty is to avoid manual handling that involves a risk of injury, so far as is reasonably practicable. Where that cannot be avoided, the employer must make a suitable and sufficient assessment of the handling, using the factors in Schedule 1. The employer must then take appropriate steps to reduce the risk of injury to the lowest level reasonably practicable.
The employer must also give employees general indications of the load. Where reasonably practicable, the employer gives precise information on the weight of each load and on the heaviest side of any load whose centre of gravity is not central. An assessment is reviewed if there is reason to suspect it is no longer valid, or if the handling has undergone a significant change.
Paragraph (3), added in 2002, lists what counts when judging the risk. It names the physical suitability of the employee, the clothing and footwear worn, and the employee's knowledge and training. Also counted are the results of the general risk assessment, membership of a group identified as especially at risk, and the results of any health surveillance.
HSE's guidance book L23
HSE publishes the guidance on these Regulations as L23, Manual handling, in its fourth edition of September 2016. It is written mainly for employers, managers and safety representatives. The book explains how to avoid, assess and reduce the risk of injury from manual handling. Part 1 holds the Regulations with brief guidance, and Parts 2 to 4 give detailed guidance for risk assessments and controls. An appendix holds risk filters that pick out the tasks needing no detailed assessment. HSE's own assessment tools sit beside the book, among them the Manual handling assessment charts (the MAC tool) and the Risk assessment of pushing and pulling (RAPP) tool.
British Columbia: sections 4.46 to 4.53
The WorkSafeBC Occupational Health and Safety Regulation, Part 4, sets out what it calls the Ergonomics (MSI) Requirements. Its stated purpose is to eliminate the risk of musculoskeletal injury to workers or, if that is not practicable, to minimize it. The Regulation defines the injury as an injury or disorder of the muscles, tendons, ligaments, joints, nerves, blood vessels or related soft tissue, including a sprain, strain and inflammation, that may be caused or aggravated by work.
| Section | Subject | Duty on the employer |
|---|---|---|
| 4.47 | Risk identification | Identify the factors in the workplace that may expose workers to a risk of injury |
| 4.48 | Risk assessment | Have the risk to workers assessed once factors are identified |
| 4.50 | Risk control | Eliminate the risk or, if that is not practicable, minimize it. Interim measures go in without delay when permanent ones will be late |
| 4.51 | Education and training | Educate exposed workers in risk identification and early signs and symptoms. Train workers in the control measures assigned to them |
| 4.52 | Evaluation | Monitor the measures and review them at least annually. Correct deficiencies without undue delay |
| 4.53 | Consultation | Consult the joint committee or worker representative. Consult workers with signs or symptoms, and a representative sample of the workers doing the work |
Section 4.49 lists the factors to consider where they apply: force, repetition, duration, work postures and local contact stresses. Working reaches and heights, the size, shape and weight distribution of the objects handled, and cold temperature come next. The last group is work-recovery cycles, task variability and work rate. Section 4.50 adds that protective equipment may replace engineering or administrative controls only where those controls are not practicable.
United States: OSHA's ergonomics overview
OSHA's ergonomics page describes musculoskeletal disorders as conditions affecting muscles, nerves, blood vessels, ligaments and tendons. It names lifting heavy items, bending, reaching overhead, pushing and pulling heavy loads, awkward postures and repetitive tasks as risk factors. OSHA defines ergonomics as fitting a job to a person.
OSHA lists seven elements of an ergonomic process: management support, worker involvement, training, problem identification, early reporting of symptoms, solutions to control hazards, and evaluation of progress. A NIOSH publication, Ergonomic Guidelines for Manual Material Handling, DHHS (NIOSH) Publication No. 2007-131, is on its list of existing guidelines.
Sources
- HSE, Manual handling, Manual Handling Operations Regulations 1992, Guidance on Regulations (L23), fourth edition, September 2016, read October 16, 2026
- legislation.gov.uk, The Manual Handling Operations Regulations 1992, regulation 4, revised version, read October 16, 2026
- WorkSafeBC, OHS Regulation Part 4, General Conditions, sections 4.46 to 4.53, read October 16, 2026
- OSHA, Ergonomics: Overview, read October 16, 2026