ArbNation Join free

Manual handling duties: Great Britain's 1992 Regulations, WorkSafeBC and OSHA

Great Britain's Manual Handling Operations Regulations 1992 put a three-step duty on employers: avoid, assess, reduce. WorkSafeBC's OHS Regulation sets ergonomics duties in sections 4.46 to 4.53.

Checked against the sources at the bottom of this page on October 16, 2026. Rules, fees and pay change: the source has the last word.

This page reports what the official source says. It is not legal advice: ask the office named here.

Great Britain: the 1992 Regulations

Regulation 4 of the Manual Handling Operations Regulations 1992 sets the duties of employers. The first duty is to avoid manual handling that involves a risk of injury, so far as is reasonably practicable. Where that cannot be avoided, the employer must make a suitable and sufficient assessment of the handling, using the factors in Schedule 1. The employer must then take appropriate steps to reduce the risk of injury to the lowest level reasonably practicable.

The employer must also give employees general indications of the load. Where reasonably practicable, the employer gives precise information on the weight of each load and on the heaviest side of any load whose centre of gravity is not central. An assessment is reviewed if there is reason to suspect it is no longer valid, or if the handling has undergone a significant change.

Paragraph (3), added in 2002, lists what counts when judging the risk. It names the physical suitability of the employee, the clothing and footwear worn, and the employee's knowledge and training. Also counted are the results of the general risk assessment, membership of a group identified as especially at risk, and the results of any health surveillance.

HSE's guidance book L23

HSE publishes the guidance on these Regulations as L23, Manual handling, in its fourth edition of September 2016. It is written mainly for employers, managers and safety representatives. The book explains how to avoid, assess and reduce the risk of injury from manual handling. Part 1 holds the Regulations with brief guidance, and Parts 2 to 4 give detailed guidance for risk assessments and controls. An appendix holds risk filters that pick out the tasks needing no detailed assessment. HSE's own assessment tools sit beside the book, among them the Manual handling assessment charts (the MAC tool) and the Risk assessment of pushing and pulling (RAPP) tool.

British Columbia: sections 4.46 to 4.53

The WorkSafeBC Occupational Health and Safety Regulation, Part 4, sets out what it calls the Ergonomics (MSI) Requirements. Its stated purpose is to eliminate the risk of musculoskeletal injury to workers or, if that is not practicable, to minimize it. The Regulation defines the injury as an injury or disorder of the muscles, tendons, ligaments, joints, nerves, blood vessels or related soft tissue, including a sprain, strain and inflammation, that may be caused or aggravated by work.

WorkSafeBC OHS Regulation, ergonomics sections
SectionSubjectDuty on the employer
4.47Risk identificationIdentify the factors in the workplace that may expose workers to a risk of injury
4.48Risk assessmentHave the risk to workers assessed once factors are identified
4.50Risk controlEliminate the risk or, if that is not practicable, minimize it. Interim measures go in without delay when permanent ones will be late
4.51Education and trainingEducate exposed workers in risk identification and early signs and symptoms. Train workers in the control measures assigned to them
4.52EvaluationMonitor the measures and review them at least annually. Correct deficiencies without undue delay
4.53ConsultationConsult the joint committee or worker representative. Consult workers with signs or symptoms, and a representative sample of the workers doing the work

Section 4.49 lists the factors to consider where they apply: force, repetition, duration, work postures and local contact stresses. Working reaches and heights, the size, shape and weight distribution of the objects handled, and cold temperature come next. The last group is work-recovery cycles, task variability and work rate. Section 4.50 adds that protective equipment may replace engineering or administrative controls only where those controls are not practicable.

United States: OSHA's ergonomics overview

OSHA's ergonomics page describes musculoskeletal disorders as conditions affecting muscles, nerves, blood vessels, ligaments and tendons. It names lifting heavy items, bending, reaching overhead, pushing and pulling heavy loads, awkward postures and repetitive tasks as risk factors. OSHA defines ergonomics as fitting a job to a person.

OSHA lists seven elements of an ergonomic process: management support, worker involvement, training, problem identification, early reporting of symptoms, solutions to control hazards, and evaluation of progress. A NIOSH publication, Ergonomic Guidelines for Manual Material Handling, DHHS (NIOSH) Publication No. 2007-131, is on its list of existing guidelines.

Sources